Reliable F3QR56, Руководство пользователя

Страница: 19 / 19

4. Inlet Fitting: [Long – Standard Inlet Fitting][Short “PL” –
Wet Pipe Systems only]
5. Sprinkler Temperature Rating: See Temperature Ratings
Table
6. Sprinkler Finish: See Finish Combinations Table
7. Escutcheon/Cover Plate Finish: See Finish Combinations
Table
8. Length:
*For dry pendents and dry sidewalls: “A” Dimension
is from face of tee to face of finished ceiling or wall in
1/4” (6mm) increments. See Fig. 1 through Fig. 9.
*For dry uprights: Order dimension is from face of tee
to top of deflector in 1/4” (6mm) increments. See Fig.
10.
Notes:
1. For Dry Upright, customer is responsible for determining the
correct deflector distance from structure above.
2. Length is based on normally gauged pipe thread “make-up”
of .600” (15mm) per ANSI B2.1 (approximately 7-1/2 threads).
Installation Wrench
Model F3R Sprinkler Wrench (Standard and HB escutcheons)
Model XLO2 Sprinkler Wrench (FP Recessed and CCP
Concealed)
Reliable Automatic Sprinkler Co., Inc.
(800) 431-1588 Sales Offices
(800) 848-6051 Sales Fax
(914) 829-2042 Corporate Offices
www.reliablesprinkler.com Internet Address
Manufactured by
Recycled
Paper
Revision lines indicate updated or new data.
EG. Printed in U.S.A.
09/21 P/N 9999970175
The equipment presented in this bulletin is to be installed in accordance with the latest published Standards of the National Fire Protection Association, Factory Mutual
Research Corporation, or other similar organizations and also with the provisions of governmental codes or ordinances whenever applicable.
Products manufactured and distributed by Reliable have been protecting life and property for almost 100 years.
Installation Data
Sprinkler
Model
Escutcheon or Cover Plate
Suggested Hole Diameter in
Wall or Ceiling
Installation
Wrench
Required Centerline of Sprinkler
Tube/Inlet to Finished Ceiling
Vertical Dimension*
F3QR56 Dry
Pendent
Standard Escutcheon 2-1/8” (54 mm) F3R
Not
Applicable
HB Extended Escutcheon 2-1/2” (64 mm) F3R
F1 Recessed Escutcheon 2-1/4” (57 mm) XLO2
FP Recessed Escutcheon
2-1/2” (64 mm)
XLO2
CCP Cover Plate XLO2
F3QR56 Dry
Horizontal
Sidewall
Standard Escutcheon 2-1/8” (54 mm) F3R
4-5/8” to 12-5/8”
(118 mm to 321 mm)
HB Extended Escutcheon 2-1/2” (64 mm) F3R
F1 Recessed Escutcheon 2-1/4” (57 mm) XLO2 cULus, NYC
4-5/8” to 6-5/8”
(118 mm to 168 mm)
FP Recessed Escutcheon 2-1/2” (64 mm) XLO2
F1 Recessed Escutcheon 2-1/4” (57 mm) XLO2 FM
4-5/8” to 12-5/8”
(118 mm to 321 mm)
FP Recessed Escutcheon 2-1/2” (64 mm) XLO2
F3QR56 Dry
Upright
N/A 1-1/2” (38mm) F3R Not Applicable
*Note: Based on 5/8” (16 mm) centerline of sprinkler tube/inlet to defector vertical distance.
Maintenance
The Model F3QR56 Dry Sprinklers should be inspected and
the sprinkler system maintained in accordance with NFPA 25.
Do not remove the factory applied thermally sensitive wax fillet
between the bulb supporting cup and the wrenching boss. Do
not replace this wax with a substitute substance.
An Alternate substance may interfere with proper operation
of the sprinkler. Do not clean sprinklers with soap and water,
ammonia or any other cleaning fluids. Remove dust by using
a soft brush or gently vacuuming. Replace any sprinkler which
has been painted (other than factory applied) or damaged in any
way. A stock of spare sprinklers should be maintained to allow
quick replacement of damaged or operated sprinklers. Prior
to installation, sprinklers should be maintained in the original
cartons and packaging until used to minimize the potential for
damage to sprinklers that would cause improper operation or
non-operation.
Ordering Information
Specify:
1. Sprinkler: [Model F3QR56 Dry Pendent SIN R5714]
[Model F3QR56 Dry Horizontal Sidewall SIN R5734]
[Model F2QR Dry Upright SIN R5724]
2. Escutcheon/Cover Plate: [None][Standard escutcheon]
[Model HB extended escutcheon][Model F1 recessed
escutcheon][Model FP recessed escutcheon][Model
CCP cover plate – pendent only]
3. Inlet Threads: [1” NPT][ISO7-1R1][3/4” NPT][ISO7-
1R3/4]