Rekluse RADIUS CX Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 39

background image

Doc ID: 191-7911A

Doc Rev: 080420

Pg. 31

Disk inspection examples

When inspecting the clutch pack, the following pictures can be used
as a reference.

These are best viewed in color by viewing this

install document from www.rekluse.com/support.

Drive Plates

–

If the clutch pack is getting high amounts of heat,

purple, blue, or black color can be seen on the drive plate teeth.
See pictures below. Not all drive plates look the same and may look
different than pictured.

Normal Heat

High Heat

Excessive Heat

(Blue)

(Black)

Friction Disks

–

Due to the dark color of the friction material, the

friction disks will appear almost black as soon as they are put in oil.
During inspection, look for glazing of the friction material. Glazing
will appear shiny and feel like glass, even after oil is cleaned from
the friction disk. Not all friction disks look the same and may look
different than pictured.

Normal
Friction

Glazed
Friction

«
...
29
30
31
32
33
...
»

Содержание RADIUS CX








































Отзывы:

Нет отзывов

Похожие инструкции для RADIUS CX

Бренд: ZERO GRAVITY Страницы: 6

Бренд: NARGESA Страницы: 27

Бренд: Endress+Hauser Страницы: 28

Бренд: RayTek Страницы: 2

Бренд: Ace Bayou Страницы: 8

Бренд: iDataLink Страницы: 9

Бренд: YOELEO Страницы: 3

Yamaha Rhino 660

Бренд: Yamaha Страницы: 3

Бренд: Zagg Страницы: 2

FRONT HEADLIGHT LENS COVER

Бренд: Bimmer Jakes Страницы: 4

A44 sound rocker

Бренд: LumiSource Страницы: 8

Бренд: Hussmann Страницы: 10

Бренд: Alpine Страницы: 69

Бренд: Allen Sports Страницы: 2

Бренд: SR Suntour Страницы: 10

Бренд: Chevrolet Страницы: 494

Бренд: Hama Страницы: 138

Бренд: CB Sabbiatrici Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды