Rekluse RADIUS CX Скачать руководство пользователя страница 3

Страница: 3 / 39

Doc ID: 191-7911A

Doc Rev: 080420

Pg. 3

OVERVIEW

This guide shows you how to replace your OE (Original Equipment)
core clutch parts with your new Rekluse upgraded clutch parts. The
following parts are replaced:

Core EXP 3.0 Drive Plates

OE Friction Disks

INSTALLATION TIPS

Read the safety information sheet
included with your kit.

Protect eyes and skin

–

wear safety

glasses and thin disposable work gloves.

Read this entire document before performing any steps.

Lay the bike on its left side when replacing the clutch. This
makes the clutch work easier and eliminates the need to drain
the oil.

For optimal clutch performance Rekluse recommends using
fresh, clean oil that

meets JASO-MA

oil rating requirements.

Rekluse offers Factory Formulated Oil™ developed specifically

for Rekluse products. Rekluse Factory Formulated Oil is a
perfect complement to any OEM or aftermarket wet clutch. Visit

www.rekluse.com

to learn more.

Bikes with taller gearing or modified engines with increased
horsepower may require heavier wedges. These can be
purchased separately from Rekluse.

Содержание RADIUS CX








































Результаты поиска

Содержание RADIUS CX

Отзывы:

Похожие инструкции для RADIUS CX

Бренды по названию

Популярные бренды

Rekluse RADIUS CX, Инструкция по установке и эксплуатации

Результаты поиска

Содержание RADIUS CX

Отзывы:

Похожие инструкции для RADIUS CX

Бренды по названию

Популярные бренды