REID LIFTING PORTABASE PBCB00001 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 36

REID LIFTING PORTABASE PBCB00001 Скачать руководство пользователя страница 8

Fall Protection Application

Fall Protection

This section must not be read in isolation from
all other sections of this manual. Read the whole
manual before using this product.

Fall arrest:

This product is tested and conforms

to the requirements of EN795:2012 Personal Fall
Protection Equipment – Anchor Devices subject
to the configuration of the product and the Davit
being used.

When being used for fall arrest purposes, the
operator must use a body harness and a shock
absorber that complies with the relevant national
standards and regulations and that limits the
maximum allowed force (m.a.f.) to 6kN.

Each personnel lift must be properly planned,
and all weights clearly known along with a clear
understanding of the WLL and constraints of all
personal fall arrest system components.

The capabilities stated in the table below apply to
standard range systems only. If unsure about your
system consult serial labels, information filled in on
page 31 or consult your supplier. Custom versions
of the system are available tailored to specific lifting
needs. These versions are designated with a ‘C’
at the end the product number on the serial label
attached to each product.

Additional Notes for Correct Operation

& Warnings

Always carry out pre-use checks before using

this equipment. It is advised to use a buddy
system and inspection must be by a competent
person

Never walk away from the footprint of the

product or move outside designated safe
zones whilst connected to it where there is a
risk of a fall

When using the product as a fall arrest anchor

ensure there is adequate fall clearance when
working at height. A competent person should
calculate this, taking in to account all of the
components of the personal fall arrest system

Always consider the potential effects of

sharp edges, chemical reagents, electrical
conductivity, cutting, abrasion, climatic
exposure on all components of the fall
protection system, and the effect of offset
forces as a result of pendulum falls

Ensure the structure on which the product is

mounted is horizontal enough to get it to be
level (check bubble indicator) after the feet are
adjusted

If the product has been subjected to a fall

arrest or impact force it must be immediately
removed from service

Davit Radius

Counterweight Required [kg]

EN795

800mm

360kg

1000mm

360kg

1200mm

360kg

«
...
6
7
8
9
10
...
»

Содержание PORTABASE PBCB00001





































Отзывы:

Нет отзывов