background image

26

    

   

27

15180-101 Rev. F

15180-101 Rev. F

Operation

 (continued)

Measurement Mode

 (continued)

 

Contact Lens

 

The procedure for measuring a contact lens is identical to measur-

ing framed lenses, however the correct contact lens type must be 

selected in the Setup menu (either hard or soft contacts) and the 

lens stand must be replaced with the contact lens stand.

1.  To measure hard contact lenses, select “H CL” in the Setup 

menu. To measure soft contact lenses, select “S CL” in the 

Setup menu. 

2.  Change the lens stand from the standard lens stand to the con-

tact lens stand.  Refer to Figure OP-22.

3.  Place the contact lens on the contact lens stand. 

Note:

  Remove the water or moisture from the lens, and set it on 

the stand, being careful not to distort it. Take the measure-

ment quickly. 

Note:

  A bifocal contact lens cannot be measured. 

4.  Holding the contact lens stand, lower the lens holder.

5.  Center the green Cross Cursor mark by moving the lens.   Re-

fer to Figure OP-23.

6.  The message “Alignment OK” will appear on the screen when 

the lens is aligned properly.  Refer to Figure OP-24.

Note:

  The Alignment Mark represents the optical center of the 

lensmeter and the Cross Cursor represents the optical cen-

ter of the lens.

7.  Press the Memory/Add button to store the Sphere, Cylinder, 

Axis and Prism measurements. 

Note: 

If “Auto Memory” in the Setup screen is set to “On”, then the 

lens will automatically be measured once the Cross Cursor 

is centered in the middle of the Alignment Mark.  

Note:

  When the optical center is found, either automatically or 

by pressing the Memory/Add button, the Cross Cursor will 

change from green to blue, and the measurement box will 

change from gray to blue.  Refer to Figure OP-24. 

8.  To measure the other lens, select the L/R icon to switch to the 

other lens.  Follow the above steps to measure the other con-

tact lens.  Refer to Figure OP-25.

9.  When finished, print, transfer or clear the data by pressing the 

corresponding button. 

Figure OP-22  Contact Lens Stand

Figure OP-23  Right Lens

Figure OP-24  Right Lens

Figure OP-25  Left Lens

Содержание Lensometer LensChek Plus













































Отзывы: