Regency Ultimate U1500E-LP Скачать руководство пользователя страница 36

Страница: 36 / 68

36 |

Regency Ultimate™ U1500E Gas Fireplace

installation

PRIOR TO REMOVING THE BURNER, ENSURE UNIT HAS COOLED TO
ROOM TEMPERATURE, ALL POWER IS DISCONNECTED AND GAS
SUPPLY IS TURNED OFF.

1. Remove faceplate, inner frame, glass door, front deflector - see instruc-

tions in this manual.

2. Remove logs.

3. Remove burner side panels by lifting out as shown in Diagram 1.

Diagram 1 - Burner Side Panels

4. Remove enamel side panels by loosening the 2 screws (1 per side) in loca-

tions noted and remove the 2 clips (see panel instructions in this manual
for detailed instructions if required).

5. Remove front lip by removing 2 screws located on firebox floor.

6. Remove rear log tray by removing 3 screws as shown in Diagram 2 below.

7. Remove 2 screws on each side to remove ceramic mounting brackets.

Diagram 2 - Side Panel, Front Lip, Ceramic

Mounting Bracket & Log Tray Screw Locations

tooltip

Side Panel Screws

Log Tray Screws

Ceramic Mounting

Bracket screws

Front Lip Screws

Diagram 3 - Burner Screw Locations

9. You can now access the air shutter and adjust the aeration.

AERATION ADJUSTMENT

The burner aeration is factory set but may need adjusting due to either the local gas supply or altitude. Open the air shutter for a blue flame or close for a

more yellow flame.

Minimum Air Shutter Opening:

NG 3/8" Open

LP Fully Open

Note: Any damage due to carboning resulting from improperly setting the aeration controls is NOT covered under warranty.

To access the air shutter, the burner needs to be removed. See below instructions to remove the burner.

8. Remove burner by removing 3 screws in locations shown below.

Содержание Ultimate U1500E-LP





































































Результаты поиска

Содержание Ultimate U1500E-LP

Отзывы:

Похожие инструкции для Ultimate U1500E-LP

Бренды по названию

Популярные бренды

Regency Ultimate U1500E-LP, Руководство по установке

Результаты поиска

Содержание Ultimate U1500E-LP

Отзывы:

Похожие инструкции для Ultimate U1500E-LP

Бренды по названию

Популярные бренды