Regency Ultimate U1500E-LP Скачать руководство пользователя страница 35

Страница: 35 / 68

Regency Ultimate™ U1500E Gas Fireplace

| 35

installation

919-794

06.21.17

Installer Notice:

These instructions must be left

with the appliance.

10. Reinstall new burner orifi ce LP and tighten.

11. Replace the yellow "NG" label with the red "LP" label.

12. Disconnect the NG stepper motor wires from the receiver in loca-

tion shown below.

Stepper

Motor

17. Reverse steps 6-1.

18. Turn on gas supply and plug in power cord.

14. Connect the LP stepper motor to the receiver (same port the NG

stepper motor was removed.

15. Adjust burner’s air shutter to fully open for LP.

16. Remove the rear log pins from the log tray (log pins are held in

by 1 screw for each pin) Relocate the log pins from the forward
position (NG) to the rearward position (opening closer to the back
wall of the unit) (LP) as shown below. Secure the pins in the new
location using the same pins and screws removed.

13. Remove NG stepper motor by removing 2 screws in locations

shown below. Replace with LP stepper motor, secure in place
with 2 screws.

19. Check for gas leaks.

20. Check inlet and outlet pressures.

21. Check operation of fl ame control.

U1500E

Содержание Ultimate U1500E-LP





































































Результаты поиска

Содержание Ultimate U1500E-LP

Отзывы:

Похожие инструкции для Ultimate U1500E-LP

Бренды по названию

Популярные бренды

Regency Ultimate U1500E-LP, Руководство по установке

Результаты поиска

Содержание Ultimate U1500E-LP

Отзывы:

Похожие инструкции для Ultimate U1500E-LP

Бренды по названию

Популярные бренды