Regency Ultimate U1500E-LP Скачать руководство пользователя страница 23

Страница: 23 / 68

Regency Ultimate™ U1500E Gas Fireplace

| 23

installation

HORIZONTAL TERMINATIONS

FLEX VENT 5" X 8"

These venting systems, in combination with the U1500E Direct Vent Gas Fireplace, has been tested and listed as a direct vent heater system by

Intertek. The location of the termination cap must conform to the requirements in the Vent Terminal Locations diagram in "Exterior Vent Termination

Locations" section.

Regency

Direct Vent (Flex) System 4 foot Termination Kit (Part# 946-615), 6 foot Termination (Part# 946-618) or 10 foot Termination Kit

(Part# 946-616) includes all the parts needed to install the U1500E.

Notes:
1)  Liner sections should be continuous without any joints or seams.
2)  Only Flex pipe purchased from Regency may be used for Flex installations.
3)  Regency

Direct Vent System (Flex) is only approved for horizontal terminations.

NOTE: If longer runs are required the FPI Direct Vent system (Flex) #946-616 includes

all parts needed to install the U1500E with a maximum 10' run.

FPI Kit #

Length Contains:

#946-615

4 Feet

8” flexible liner (Kit length)

5” flexible liner (Kit length)

spring spacers

thimble

AstroCap XL

termination cap

screws

tube of Mill Pac

plated screws

S.S. screws #8 x 1-1/2” drill point

10)

vinyl siding standoff

#946-618

6 Feet

#946-616

10 Feet

IMPORTANT

Must use Rear Venting Deflector

packaged with unit in rear vent

horizontal termination applications.

203mm dia.

Flue pipe

127mm dia. flue pipe

spring spacer

Termination Cap

AstroCap XL

(Part #946-623/P)

Flue Guard - if required*

(Part #946-506/P)

Wall Thimble

(Mandatory in all

Horizontal Terminations)

(Part 946-604/P)

Содержание Ultimate U1500E-LP





































































Результаты поиска

Содержание Ultimate U1500E-LP

Отзывы:

Похожие инструкции для Ultimate U1500E-LP

Бренды по названию

Популярные бренды

Regency Ultimate U1500E-LP, Руководство по установке

Результаты поиска

Содержание Ultimate U1500E-LP

Отзывы:

Похожие инструкции для Ultimate U1500E-LP

Бренды по названию

Популярные бренды