Regency Ultimate U1500E-LP Скачать руководство пользователя страница 1

Страница: 1 / 68

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4

919-792

07.17.17

Tested by:

Installer

: Please complete the details on the back cover

and leave this manual with the homeowner.

Homeowner:

Please keep these instructions for future reference.

www.regency-fire.com

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other

appliance.

- WHAT TO DO IF YOU SMELL GAS
•

Do not try to light any appliance.

• Do not touch any electrical switch: do not use any phone in your building.

Leave the building immediately.

• Immediately call your gas supplier from a neighbour's phone. Follow the gas supplier's

instructions.

• If you cannot reach you gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency or the gas supplier.

WARNING
FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious
injury, death, or property damage.

Regency Ultimate

™

U1500E

Gas Fireplace

Owners &

Installation Manual

MODELS: U1

500E-NG Natural Gas

500E-LP Propane

Содержание Ultimate U1500E-LP





































































Результаты поиска

Содержание Ultimate U1500E-LP

Отзывы:

Похожие инструкции для Ultimate U1500E-LP

Бренды по названию

Популярные бренды

Regency Ultimate U1500E-LP, Руководство по установке

Результаты поиска

Содержание Ultimate U1500E-LP

Отзывы:

Похожие инструкции для Ultimate U1500E-LP

Бренды по названию

Популярные бренды