Regency U900E Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 64

background image

44 |

Regency Ultimate™ U900E Gas Fireplace

installation

SCREEN & INNER DOOR FRAME INSTALLATION

919-691

08.03.16

1

SAFETY SCREEN / INNER DOOR FRAME REMOVAL/INSTALLATION

THE INNER DOOR FRAME (3) MUST BE PURCHASED SEPARATELY IN EITHER STAINLESS STEEL OR BLACK

1. The inner door trim (1) and safety screen (2) come attached to the fireplace.

Remove the inner door trim and safety screen by pulling the bottom of the
trim towards you as one, then lift up.

3. Install screen into inner door frame - secure safety screen by bending in 6

tabs in locations shown below.

4. Hook the inner door frame (3) and safety screen assembly (2) over

the inner door trim.

1

5. Bend the center tab up and secure with a screw to attach the inner

door frame/safety screen assembly to the inner door trim

7. Attach completed assembly to the glass door on unit.

8. Secure the assembly with 1 screw on each side.

Note:

Bottom of frame is secured to glass door frame with left and right
magnets.

2

3

Tabs

2. Remove screws from inner side of the inner door trim and discard screws

and the brackets. (Brackets not shown). Remove the screen mesh from
inner door trim.

Screw Locations

6. Bend in magnetic tabs—located in lower corners of the frame (lower

left shown below).

«
...
42
43
44
45
46
...
»

Содержание U900E

































































Отзывы:

Нет отзывов

Похожие инструкции для U900E

Бренд: Valcourt Страницы: 32

Бренд: Unigas Страницы: 68

Бренд: Jetmaster Страницы: 29

Бренд: Mayer Barbecue Страницы: 8

34 Zircon Direct Vent

Бренд: Malm Fireplaces Страницы: 58

Бренд: Desa Страницы: 44

Бренд: Superior Страницы: 20

ISOKERN Standard 36

Бренд: EarthCore Страницы: 12

CHIMENEA SRCH06D

Бренд: BIGHORN Страницы: 8

Abbotsford 064-4015-0

Бренд: Canvas Страницы: 104

Бренд: Vermont Castings Страницы: 14

Comfort Glow CGEFP33PR

Бренд: Desa Страницы: 38

Бренд: Qindao Hichanse Group Страницы: 16

FIREPOD universal

Бренд: ADVANCE Easy Moving Страницы: 24

Бренд: Valor Страницы: 14

Бренд: Napoleon Страницы: 6

Бренд: Napoleon Страницы: 80

Бренд: Archgard Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды