Regency U900E Скачать руководство пользователя страница 22

Страница: 22 / 64

22 |

Regency Ultimate™ U900E Gas Fireplace

installation

VENTING

DIRECT VENT SYSTEM (FLEX)

HORIZONTAL TERMINATIONS ONLY

These venting systems, in combination with the U900E Direct Vent Gas Fireplace, have been tested and listed as a direct vent heater system by

Warnock Hersey/ITS. The location of the termination cap must conform to the requirements in the Vent Terminal Locations diagram in the "Exterior

Vent Termination Locations" section.

Regency Direct Vent (Flex) System Termination Kit (Part # 946-515) includes all the parts needed to install the U900E with a maximum

run of 4 feet.

6-7/8" dia. flexible liner (4 ft. length)

4" dia. flexible liner (4 ft. length)

spring spacers (4)

thimble (2)

AstroCap

termination cap (1)

screws (12)

tube of Mill Pac (1)

plated screws (8)

screws #8 x 1-1/2" Drill Point, Stainless

Steel (4)

6-7/8" dia. flexible liner (10 ft. length)

4" dia. flexible liner (10 ft. length)

spring spacers (7)

thimble (2)

AstroCap

termination cap (1)

screws (12)

tube of Mill Pac (1)

plated screws (8)

screws #8 x 1-1/2" Drill Point, Stainless

Steel (4)

If longer runs are needed, the Regency Direct

Vent system (Flex) # 946-516 includes all

the parts needed to install the U900E with a

maximum 10' run.

Notes:

1) Liner sections must be continuous without any joints or seams.

2) Only Flex pipe purchased from Regency may be used for Flex installations.

Содержание U900E

































































Результаты поиска

Содержание U900E

Отзывы:

Похожие инструкции для U900E

Бренды по названию

Популярные бренды

Regency U900E, Инструкция для владельца и по установке

Результаты поиска

Содержание U900E

Отзывы:

Похожие инструкции для U900E

Бренды по названию

Популярные бренды