Regency U900E Скачать руководство пользователя страница 13

Страница: 13 / 64

Regency Ultimate™ U900E Gas Fireplace

| 13

installation

FRAMING DIMENSIONS

Framing

Dimensions

Description

U900E

Framing Height

42-1/4" (1073mm)

Framing Width

45" (1143mm)

Framing Depth

22-3/4" (578mm)

Minimum Height to Combustibles

52-1/4" (1327mm)

Corner Facing Wall Depth

51-1/2" (1308mm)

Corner Facing Wall Width

72-1/2"(1842mm)

Vent Centerline Height

39" (991mm)

Non-combustible facing height

20" (508mm)

Gas Connection Opening Height

1-11/16" (43mm)

Gas Connection Height

2-11/16" (67mm)

Gas Connection Inset

1-1/8" (29mm)

Gas Connection Opening Width

4-11/16" (119mm)

Framing depth measurement is noted with the nailing strips set as far forward on the firebox as possible.

The nailing strips can be adjusted back up to 1-1/2" (38mm) to allow for varying thicknesses in non-combustible

material & wall finishes.

The non combustible board is supplied to meet the requirements for this appliance. See non combustible section in this manual for details.

Steel header on edge

Содержание U900E

































































Результаты поиска

Содержание U900E

Отзывы:

Похожие инструкции для U900E

Бренды по названию

Популярные бренды

Regency U900E, Инструкция для владельца и по установке

Результаты поиска

Содержание U900E

Отзывы:

Похожие инструкции для U900E

Бренды по названию

Популярные бренды