Regency U900E Скачать руководство пользователя страница 1

Страница: 1 / 64

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4

919-625c

12.14.16

Tested by:

Installer

: Please complete the details on the back cover

and leave this manual with the homeowner.

Homeowner:

Please keep these instructions for future reference.

www.regency-fire.com

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other

appliance.

- WHAT TO DO IF YOU SMELL GAS
•

Do not try to light any appliance.

• Do not touch any electrical switch: do not use any phone in your building.

Leave the building immediately.

• Immediately call your gas supplier from a neighbour's phone. Follow the gas supplier's

instructions.

• If you cannot reach you gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency or the gas supplier.

WARNING
FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious
injury, death, or property damage.

Regency Ultimate

™

U900E

Gas Fireplace

Owners &

Installation Manual

MODELS: U9

00E-NG Natural Gas

00E-LP Propane

Содержание U900E

































































Результаты поиска

Содержание U900E

Отзывы:

Похожие инструкции для U900E

Бренды по названию

Популярные бренды

Regency U900E, Инструкция для владельца и по установке

Результаты поиска

Содержание U900E

Отзывы:

Похожие инструкции для U900E

Бренды по названию

Популярные бренды