Regency PG36 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 48

background image

Regency

®

PG36-5 Gas Log Fireplace

6

INSTALLATION

Clearances for Bay or Flush Front

NOTE: The minimum fl oor clearance must
be maintained from the top surface of the
carpeting, tile, etc.

Minimum Clearance from Top of Unit to:
Mantel*

Minimum

7" (177mm)

Ceiling

from top of unit.

32" (1016mm)

Side Wall Clearance
Bay or Flush Front

6"

(152mm)

Horizontal Flue Clearances

Top

2" (51mm)

Side

1-1/2"

(38mm)

Bottom

1-1/2"

(38mm)

Vertical Flue Clearances

1-1/4"

(32mm)

Alcove Clearances**:
Max.

Depth

36"

(914mm)

Min.

Width

48"

1219mm)

Min.

Height

72"

1829mm)

* see mantle clearance instructions
(Refer to the "Combustible Mantels," & "Mantel
Leg Clearances" sections.)

CLEARANCES

The clearances listed below are Minimum
distances unless otherwise stated:

A major cause of chimney related fi res is
failure to maintain required clearances (air
space) to combustible materials. It is of the
greatest importance that this fi replace and
fl ue system be installed only in accordance
with these instructions.

Clearance to Combustibles from:
Back

0"

(0mm)

Side

0"

(0mm)

Floor

0

"

(0mm)

Diagram 1

LOCATING YOUR

FIREPLACE

1)

When selecting a location for your fi replace,

ensure that the clearances outlined on this
page are met.

2)

Provide adequate clearances for servicing.

3)

The appliance must be installed on a fl at,

solid, continuous surface (e.g. wood, metal,
concrete). This may be the fl oor, or raised up
on a platform to enhance its visual impact.
If the appliance is going to be installed
on carpeting, combustible linoleum tile or
other combustible material other than wood
fl ooring, the appliance must be installed on
a metal or wood panel extending the full
width and depth of the appliance.

4)

The PG36 Co Axial Flue Gas Fireplace

can be installed in a recessed position or
framed out into the room as in A, B, C, D.
See Diagram 1.

5)

This appliance is Listed for bedroom

installations when used with a Listed Millivolt
Thermostat. Some areas may have further
requirements, check local codes before
installation.

6)

The PG36 Co Axial Flue Gas Fireplace is

approved for alcove installations, which
meet the clearances listed on this page.

7)

We recommend that you plan your installation
on paper using exact measurements for
clearances and fl oor protection before
actually installing this appliance. Have an
authorized inspector, dealer, or installer
review your plans before installation.

Note: For fl ue terminations see the "Exterior

Flue Termination Locations" section.

MANUFACTURED

MOBILE HOME

ADDITIONAL

REQUIREMENTS

1)

Ensure that structural members are not cut

or weakened during installation.

2)

Ensure proper grounding using the #8

ground lug provided. Refer to the "Wiring"
section.

A)

Flat on Wall

B)

Flat on Wall Corner

C)

Recessed into Wall/Alcove

D)

Corner

WARNING

Fire hazard is an extreme

risk if these clearances

are not adhered to.

«
...
4
5
6
7
8
...
»

Содержание PG36

















































Отзывы:

Нет отзывов

Похожие инструкции для PG36

Бренд: Jetmaster Страницы: 13

Бренд: Cannon Страницы: 24

Бренд: Parkwood Страницы: 40

Бренд: Blue Rhino Страницы: 16

Бренд: Napoleon Страницы: 32

Бренд: Twin-Star International Страницы: 19

Бренд: Bali Страницы: 16

Бренд: Piazzetta Страницы: 48

Бренд: pleasant hearth Страницы: 18

CASUAL FIRESIDE 5110-2872O-E

Бренд: OW Lee Страницы: 28

SUPERIOR B-VENT 500 Series

Бренд: Lennox Hearth Products Страницы: 16

RHAPSODY RHAP42N

Бренд: IHP Страницы: 6

Бренд: Piazzetta Страницы: 61

Бренд: FocalPoint Страницы: 7

Бренд: Vermont Castings Страницы: 12

Бренд: Vermont Castings Страницы: 28

Бренд: Vermont Castings Страницы: 32

GreenSmart Fireplace 564 SS

Бренд: Travis Industries Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды