background image

Regency PG33NG4-R Gas Inbuilt

5

installation

IMPORTANT:  

SAVE THESE 

INSTRUCTIONS

The P33-NG or P33-LPG Direct Flue Fireplace must 

be installed in accordance with these instructions. 

Carefully read all the instructions in this manual 

first. Consult the "authority having jurisdiction" to 

determine the need for a permit prior to starting the 

installation. It is the responsibility of the installer 

to ensure this fireplace is installed in compliance 

with manufacturer's instructions and all applicable 

codes.

BEFORE YOU START

Safe installation and operation of this appliance 

requires common sense, however, we are required 

by the Canadian Safety Standards and ANSI Stand

-

ards to make you aware of the following:

MANUFACTURED 

MOBILE HOME

ADDITIONAL 

REQUIREMENTS

1)

  Ensure that structural members are not cut or 

weakened during installation.

2)

  Ensure proper grounding using the #8 ground 

lug provided. See page 35.

GENERAL SAFETY IN-

FORMATION

1)

  The appliance shall be installed in accord-

ance  with  the  manufacturer's  installation 

instructions,local  gas  fitting  regulations,  mu

-

nicipal building codes, water supply regulations, 

electrical wiring regulations, with AS5601-2004 

(AGA gas installation code) NZS 5261 (New 

Zealand)

2)

 

Installation and repair should be done ONLY 

by an authorised person.  

3)

 

THIS APPLIANCE IS NOT INTENDED AS A 

FIREPLACE INSERT. DO NOT CONNECT TO 

MASONARY FLUE.

4)

 

This appliance must be connected to the 

specified  flue  and  termination  cap  to  the 

outside of the building envelope. Never flue 

to another room or inside a building. Make 

sure  that  the  flue  is  fitted  as  per  Flueing 

instructions.

5)

  Inspect the flueing system annually for blockage 

and any signs of deterioration.   

6)

  Flueing terminals shall not be recessed into a 

wall or siding.

7)

  Any safety glass removed for servicing must 

be replaced prior to operating the appliance.

8)

  To prevent injury, do not allow anyone who is 

unfamiliar with the operation to use the fireplace.

9)

  Wear gloves and safety glasses for protection 

while doing required maintenance.

10)

 Be aware of electrical wiring locations in walls 

and ceilings when cutting holes for termination.

11)

 Under no circumstances should this appliance 

be modified. Parts that have to be removed for 

servicing should be replaced prior to operating 

this appliance.

12)

 Installation and any repairs to this appliance 

should be done by an authorised service per

-

son. An authorised service person should be 

called to inspect this appliance annually. Make 

it a practice to have all of your gas appliances 

checked annually.

13)

 Do not slam shut or strike the glass door.

14)

 Under no circumstances should any solid fuels 

(wood, paper, cardboard, coal, etc.) be used in 

this appliance.

15)

 The  appliance  area  must  be  kept  clear  and 

free of combustible materials, (gases and other 

flammable vapours and liquids).

CLOTHING OR OTHER FLAMMABLE 
MATERIAL SHOULD NOT BE PLACED 
ON OR NEAR THE APPLIANCE.

   

CHILDREN AND ADULTS SHOULD BE 
ALERTED TO THE HAZARDS OF HIGH 
SURFACE TEMPERATURES,  ESPE-
CIALLY THE FIREPLACE GLASS, AND 
SHOULD STAY AWAY TO AVOID BURNS 
OR CLOTHING IGNITION.  

INSTALLATION AND REPAIR SHOULD 
BE DONE BY AN AUTHORIZED 
SERVICE PERSON. THE APPLIANCE 
SHOULD BE INSPECTED BEFORE 
USE AND AT LEAST ANNUALLY BY A 
PROFESSIONAL SERVICE PERSON. 
MORE FREQUENT CLEANING MAY 
BE REQUIRED DUE TO EXCESSIVE 
LINT FROM CARPETING, BEDDING 
MATERIAL, ETC. IT IS IMPERATIVE THAT 
CONTROL COMPARTMENTS, BURNERS 
AND CIRCULATING AIR PASSAGEWAYS 
OF THE APPLIANCE BE KEPT CLEAN.

DUE TO HIGH TEMPERATURES, THE 
APPLIANCE SHOULD BE LOCATED 
OUT OF TRAFFIC AND AWAY FROM 
FURNITURE AND DRAPERIES.

WARNING: FAILURE TO INSTALL THIS 
APPLIANCE CORRECTLY WILL VOID 
YOUR WARRANTY AND MAY CAUSE A 
SERIOUS HOUSE FIRE.

YOUNG CHILDREN SHOULD BE CARE-
FULLY  SUPERVISED WHEN THEY ARE 
IN THE SAME AREA AS THE APPLI-
ANCE.  TODDLERS, YOUNG CHILDREN 
AND OTHERS MAY BE SUSCEPTIBLE 
TO ACCIDENTAL CONTACT BURNS.  A 
PHYSICAL BARRIERS IS RECOMMEND-
ED IF THERE ARE AT RISK INDIVIDUAL 
IN THE HOUSE.  TO RESTRICT ACCESS 
TO A FIREPLACE OR STOVE, INSTALL 
AN ADJUSTABLE SAFETY GATE TO 
KEEP TODDLERS, YOUNG  CHILDREN 
AND OTHER AT RISK INDIVIDUALS OUT 
OF THE ROOM AND AWAY FROM HOT 
SURFACES. 

Содержание Panorama PG33LPG4-R

















































Отзывы: