Regency PANORAMA P33E Скачать руководство пользователя страница 60

Страница: 60 / 64

Regency® P33E-10 Zero Clearance Direct Vent Gas Fireplace

warranty

Products made or provided by other manufacturers and used in conjun

cti

on with the FPI appliance without prior

authoriza

on from FPI may void this warranty.

Limita

ons of Liability:

The original purchaser’s exclusive remedy, and FPI’s sole obliga

tio

n under this warranty, express or implied, in

contract or in tort, shall be limited to replacement, repair, or refund, as outlined above. In no event will FPI be

liable for any incidental or consequen

al damages caused by defects in this product. TO THE EXTENT PERMITTED

BY APPLICABLE LAW, FPI MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY SPECIFIED HEREIN. THE

DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE EXPRESSED WARRANTY SPECIFIED

ABOVE. IF IMPLIED WARRANTIES CANNOT BE DISCLAIMED, THEN SUCH WARRANTIES ARE LIMITED IN DURATION

TO THE DURATION OF THIS WARRANTY. Any recovery is limited to the original purchase price. No other person is

authorized to modify this Limited Life

me Warranty, and your seller is solely responsible for any other warran

tie

For USA Consumers: Some states do not allow limita

ons on how long an implied warranty lasts, or allow exclusion

or limita

on of incidental or consequen

al damages, so the above limita

ons or exclusions may not apply to you.

This warranty gives you speci

ﬁc l

egal rights, and you may also have other rights, which vary from state to state.

Residents of New Jersey are governed by that state's consumer pro

tectio

n laws.

For Canadian Consumers: Residents of Quebec are governed by that province's consumer pro

tectio

n legisla

tio

Instruc

ons:

To obtain warranty service, please contact your authorized selling dealer

. If your authorized selling dealer is no

longer reachable, please contact us below:

For purchases made in

CANADA or the UNITED STATES

Visit Regency’s Web Site:

www.regency-

ﬁr

e.com

Or call the Regency Customer Care Centre

Hours of Opera

on: 7:00am – 4:00pm PST (Monday to Friday, excluding Statutory Holidays)

Phone: 604-946-5155 / Fax: 604-946-4349

Canadian Corporate Mailing Address

FPI Fireplace Products Intern

atio

nal Ltd.

6988 Venture St.

Delta,

Briti

sh Columbia

Canada, V4G 1H4

US Corporate Mailing Address

Fireplace Products U.S., Inc.

PO Box 2189 PMB 125

Blaine, WA

United States, 98231

Product Registra

on and Customer Support:

Thank you for choosing a Regency Fireplace. Regency strives to be a world leader in the design, manufacture, and

mar

keti

ng of hearth products. To provide the best support for your product, we request that you complete a

product registra

on form at

p://www.regency-

ﬁ

re.com/Customer-Care/Warranty-Registra

on.aspx

within

ninety (90) days of purchase.

Содержание PANORAMA P33E

































































Результаты поиска

Содержание PANORAMA P33E

Отзывы:

Похожие инструкции для PANORAMA P33E

Бренды по названию

Популярные бренды

Regency PANORAMA P33E, Инструкция для владельца и по установке

Результаты поиска

Содержание PANORAMA P33E

Отзывы:

Похожие инструкции для PANORAMA P33E

Бренды по названию

Популярные бренды