Regency HZI390E Скачать руководство пользователя | Manualshive

Страница: 30 / 56

background image

30

L390E-2 / HZI390E-2 Direct Vent Gas Insert

INSTALLATION

The L390E / HZI390E use a heat exchanger and effi cient combustion
technology to provide extreme heating effi ciencies. The more effi cient an ap-
pliance becomes, the lower the fl ue gas temperatures becomes.
On start-up, fl ue temperatures are required to initiate venting action.

Here are some considerations when setting up the L390E / HZI390E:

1)

When operating the unit in temperatures below 50

°

F, run the pilot in

"Standing Pilot" mode, by setting the Surefi re™ switch to ON.

The switch is located to the bottom left of the Firebox Door.

Move the switch to the right to run in Standing Pilot mode, to the left to

run in Intermittent Pilot (electronic ignition) mode. This will aid in keeping
the fl ue slightly warmer than the outside air, making start up a smoother
process.

STANDING PILOT

Standing

Pilot On/Off

Exhaust Baffle

Screws help to locate
the Exhaust Baffle when
installing in the Firebox

Exhaust Baffle

Exhaust Baffle Screws (both sides)

Exhaust Baffle

Screw

Heat Exchanger Return

Heat Exchanger Return

ADDING THE HEAT EXCHANGER RETURN

1)

Remove the panels if they are already installed. Remove one screw

in the upper left and upper right of the fi rebox. If the unit has been
previously operated, spray these screws with WD-40. Once the screws
have been removed, lower the front edge of the exhaust baffl e and pull
towards you. There are 3 screws at the rear of the exhaust baffl e that
help to position the baffl e and keep it straight during operation.

2)

Install the heat exchange return as shown.

3)

Reinstall the exhaust baffl e.

Surefi re switch for standing pilot

HEAT EXCHANGE RETURN

NOTE:

Only installed at elevations of 35 feet or higher.

«
...
28
29
30
31
32
...
»

Содержание HZI390E

























































Отзывы:

Нет отзывов

Похожие инструкции для HZI390E

Бренд: Klarstein Страницы: 76

Бренд: Napoleon Страницы: 80

Argon Built In ARBI100

Бренд: Stanley Страницы: 12

Бренд: Napoleon Страницы: 4

Бренд: Infinity Страницы: 32

Black Beauty Radiant 340

Бренд: Valor Страницы: 9

C11810LP Sedona

Бренд: Real Flame Страницы: 48

MODEL OSBURN STRATFORD

Бренд: Stove Builder International Страницы: 38

Бренд: QualityCraft Страницы: 12

Бренд: Century Heating Страницы: 30

Бренд: Vanguard Страницы: 32

Бренд: Kenwood Страницы: 24

Бренд: Kenwood Страницы: 42

Бренд: Kenwood Страницы: 47

Бренд: Rasmussen Страницы: 18

Бренд: Lopi Страницы: 40

Бренд: Lopi Страницы: 15

864 TRV 31K CleanFace

Бренд: Lopi Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды