Regency HZI390E Скачать руководство пользователя | Manualshive

Страница: 17 / 56

background image

L390E-2 / HZI390E-2 Direct Vent Gas Insert

17

INSTALLATION

Before you begin:

Shut off the gas supply to the unit.
Disconnect all electrical supply to the unit.

Always let the appliance cool to room temperature before servicing.

1)

Remove the left side control cover.

2)

Loosen both screws at the top of the valve about ½ way out. Lift the

valve body and lean outward. The Valve Brackets will rest open as
shown on the right.

3)

Disconnect the Cable coming from the Pressure Regulator Motor.

WARNING

This conversion kit shall be installed by a qualifi ed service agency in
accordance with the manufacturer’s instructions and all applicable codes
and requirements of the authority having jurisdiction. If these instructions
is not followed exactly, a fi re, explosion or production of carbon monoxide
may result causing property damage, personal injury or loss of life. The
qualifi ed service agency is responsible for the proper installation of this
kit. The installation is not proper and complete until the operation of the
converted appliance is checked as specifi ed in the manufacturer’s instruc-
tions supplied with the kit.

THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER

IF IN DOUBT DO NOT DO THIS CONVERSION!

Side control cover

Cable from motor

The valve in the L390E is attached using 2 screws and 2 hooks located

below the valve. Loosening the screws part way and lift the valve to
disengage the hooks.

The valve will then hinge outward allowing access to the components

and pressure taps located on the top of the valve without completely
removing the valve.

Conversion Kit 396-972 includes:

1

911-011

Stepper Motor LP for 885 SIT

1

904-947

Orifi ce #53

1

910-101

Orifi ce #35

1

918-590

Decal - Conversion to LP

1

908-528

Label Propane

4)

Remove and discard 2 Pressure regulator screws A (T20 or slot), Pres-
sure Regulator B, Spring and Diaphragm C.

5)

Ensure the rubber gasket, which is prefi tted as part of the Assembly,

is properly positioned. Install the new Pressure Regulator using the 2x
M4 x .7 screws supplied. Tighten the screws to 25lb-in. In the event that
the screw threads are cross threaded or stripped, replace the valve
assembly.

Install the enclosed propane identifi cation label to the valve body where it
can be easily seen.

CONVERSION FROM NG TO LP

L390E-2/HZI390E-2 using SIT 885 NOVA Gas Valve

«
...
15
16
17
18
19
...
»

Содержание HZI390E

























































Отзывы:

Нет отзывов

Похожие инструкции для HZI390E

COLLETTE L-FT629PST-A

Бренд: HAMPTON BAY Страницы: 6

Бренд: HAMPTON BAY Страницы: 48

Бренд: La Hacienda Страницы: 4

Бренд: Uniflame Страницы: 16

Бренд: DutchWest Страницы: 32

Бренд: Paramount Fitness Страницы: 24

Бренд: Majestic fireplaces Страницы: 24

Бренд: crystal fires Страницы: 26

Бренд: Dimplex Страницы: 15

ALLURE NEFVC32H

Бренд: Napoleon Страницы: 4

Бренд: Comfort Flame Страницы: 28

Savannah Chat P33442G

Бренд: Paragon Casual Страницы: 15

Бренд: baltur Страницы: 92

Бренд: Jøtul Страницы: 92

Бренд: Napoleon Страницы: 24

Бренд: Napoleon Страницы: 16

Бренд: Napoleon Страницы: 40

Haliburton GDS28N

Бренд: Napoleon Страницы: 96

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды