Regency Horizon HZ42E-LP Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 60

background image

42

HZ42E Regency Horizon™ Gas Fireplace

INSTALLATION

OPTIONAL REFLECTIVE PANEL INSTALLATION

1)

Position the left side panel in place -

top of panel in fi rst

, then fi t the

bottom tab into the slot at the bottom of the fi rebox as shown below.
Repeat for right side panel.

Fit side panel tab into slot

Left Side

Panel

Shown

Left side panel in position

2)

Fit the back panel into position by clearing the pilot shield -

bottom

of panel goes in fi rst.

Then fi t the tabs on the bottom left and right side of the back panel

into the slots at the base of the fi rebox.

Secure the back panel in place by placing the brackets over the
screws on the top of the inside left and right side of the fi rebox and
tighten the screw to hold the bracket against the back panel shown
below.

Right side back panel tab fi tted into slot

Bracket shown in place on right side of the fi rebox

Right side panel in position

Before installation, panels must be handled and cleaned as per instructions noted below:

Stainless Steel Panels

Black Enamel Panels

•

Stainless panels must be inspected for scratches and dimples prior

to installation. All claims to be recorded at this time.
Claims for damage after installation will not receive consideration.

•

Black Enamel panels must be inspected for scratches and dimples

prior to installation. All claims to be recorded at this time.
Claims for damage after installation will not receive consideration.

•

Use a hair dryer to remove the protective coating from the panels.

•

To protect the fi nish during installation and handling

- cotton gloves

MUST

be worn at all times while handling the panels.

•

Stainless panels will discolor a little during normal operation.

This is normal and should not be considered a defect.

•

Black Enamel panels will discolor a little during normal operation. This

is normal and should not be considered a defect.

*

All hand and fi nger marks

MUST

be cleaned off with a soft cloth and

a stainless steel cleaner. Most stainless steel cleaners leave a fi lm/
residue on the surface of the panels. Use an ammonia based cleaner
(ie. glass cleaner) to remove this fi lm before applying heat to the unit.

Failure to do this will result in burn stains on panels which you
will be unable to remove.

Not protected by product warranty.

*

All hand and fi nger marks

MUST

be cleaned off with a soft cloth. Use

an ammonia based cleaner (ie. glass cleaner) to remove any fi ngerprints
before applying heat to the unit.

Failure to do this will result in burn stain on panels which you
will be unable to remove.

Not protected by product warranty.

90 degree

bend faces

towards center

of unit on both

left and right

side panels

Left Side

Bracket

«
...
40
41
42
43
44
...
»

Содержание Horizon HZ42E-LP





























































Отзывы:

Нет отзывов

Похожие инструкции для Horizon HZ42E-LP

Siena Fire SNA20

Бренд: Dimplex Страницы: 3

Бренд: barbas Страницы: 32

Бренд: Country Living Страницы: 10

MONTANA MONTANA-36

Бренд: Outdoor Lifestyles Страницы: 45

Бренд: Desa Страницы: 40

Бренд: Desa Страницы: 32

Бренд: Desa Страницы: 36

Бренд: Quadra-Fire Страницы: 28

Бренд: Heat & Glo Страницы: 25

Бренд: Heat & Glo Страницы: 48

Бренд: Paragon Страницы: 24

MONTECITO ESTATE CAT

Бренд: Astria Fireplaces Страницы: 32

Бренд: Walltherm Страницы: 11

TWILIGHT-II-MOD

Бренд: Outdoor Lifestyles Страницы: 41

Бренд: Pride Family Brands Страницы: 8

Бренд: for Living Страницы: 7

Бренд: for Living Страницы: 7

Бренд: Bayside Furnishings Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды