Regency Horizon HZ42E-LP Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 60

background image

HZ42E Regency Horizon™ Gas Fireplace

3

MANUFACTURED MOBILE HOME REQUIREMENTS

INFORMATION FOR MOBILE/MANUFACTURED HOMES AFTER FIRST SALE

This Regency

®

product has been tested and listed by Warnock Hersey/Intertek as a Direct Vent Wall Furnace to the following standards:

VENTED GAS FIREPLACE HEATERS ANSI Z21.88a-2007 / CSA 2.33a-2007 and GAS-FIRED APPLIANCES FOR USE AT HIGH ALTITUDES
CAN / CGA 2.17-M91.

This Direct Vent System Appliance must be installed in accordance with the manufacturer's installation instructions and the Manufactured
Home Construction and Safety Standard, Title 24 CFR, Part 3280, or the current Standard of Fire Safety Criteria for Manufactured Home
Installations, Sites, and Communities ANSI/NFPA 501A, and with CAN/CSA Z240-MH Mobile Home Standard in Canada.

This appliance installation must comply with the manufacturer's installation instructions and local codes, if any. In the absence of local codes
follow the current National Fuel Gas Code, ANSI Z223.1 and the current National Electrical Code ANSI/NFPA 70 in the U.S.A., and the current
CAN/CGA B149 Gas Installation Code and the current Canadian Electrical Code CSA C22.1 in Canada.

This appliance comes equipped with a dedicated #8 Ground Lug for attachment of the ground wire to the steel chassis as applicable to
local codes.

The appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the
National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1.

This appliance may only be installed in an aftermarket permanently located, manufactured (U.S.A only) or mobile home, where not prohibited
by local codes.

This appliance can only be used with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases.

Ensure that structural members are not cut or weakened during installation.

«
1
2
3
4
5
...
»

Содержание Horizon HZ42E-LP





























































Отзывы:

Нет отзывов

Похожие инструкции для Horizon HZ42E-LP

Бренд: Napoleon Страницы: 4

Бренд: Valor Fires Страницы: 48

Бренд: Valor Fires Страницы: 48

Бренд: Valor fiers Страницы: 52

Бренд: L'Artistico Страницы: 48

Бренд: Napoleon Страницы: 56

Бренд: Nectre Fireplaces Страницы: 6

Бренд: Unigas Страницы: 68

Бренд: Jetmaster Страницы: 29

Бренд: Glow Fire Страницы: 73

Бренд: Napoleon Страницы: 4

Бренд: Valor Страницы: 48

Argon Built 3 Sided

Бренд: Stanley Страницы: 26

Бренд: Stellar Hearth Страницы: 51

Бренд: Everwarm Страницы: 25

Бренд: Malm Fireplaces Страницы: 9

Бренд: KAL-FIRE Страницы: 72

Surefire FCC 16

Бренд: Burley Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды