Regency E18-LP Скачать руководство пользователя страница 44

Страница: 44 / 77

Regency

E18 Gas Fireplace Insert

installation

Leg Height

Existing Firebox

Vent Slide Plate

Outer Shell Legs (x2)

Fastening Screws

Outer Shell Screws (x4)

Vent Slide Plate

attachement screw

Step #2: Outer Shell Installation

The E18 was designed to be

installed in a modular fashion,

making it easier for the installer to

locate and install the various

components without having to

support the weight of the entire

appliance. The Wire Harness comes

installed from factory in order that

no connections need to be made in

the field.

1) Slide the Outer Shell rearward and

into the existing firebox being

carefull to make sure that the Vent

Slide Plate is properly engaged in the

slide provisions of the Outer Shell.

Move the Outer Shell rearward until

the left and right flanges are up

against the existing firebox.

2) Adjust the Outer Shell Legs down

to the setting noted for your specific

installation. If these settings are not

correct, the Surround Panels will not

fit correctly in your particular

installation.

3) Attach the Vent Slide Plate to the

Outer Shell with one sheet metal

screw as shown. Do not attach the

Outer Shell to the existing firebox at

this point.

Drafthood

Bottom

Drafthood Slide

Control Box

Surround

Mounting

Bracket

Left

Wire Harness

Upper Drafthood

Baffle

Surround Mounting

Bracket Right

Step #3: Firebox Installation

1) Install the Upper Drafthood Baffle onto the Outer Shell using 4 screws provided.

2) The Firebox installs into the Outer Shell by sliding the Drafthood Bottom onto the Drafthood

Slide until you are able to install 4 screws to secure the Firebox, 2 located in each inner lower

Firebox Sides. While you are installing the Firebox, care must be taken to avoid damaging the

Wire Harness until it can be secured in following steps.

3) The unit is installed correctly when the flanges that secure the Firebox to the Outer Shell are

touching. Making sure that the unit is centered within the existing firebox, attach the Outer

Shell to the existing firebox using 4x sheet metal screws as shown in Step #2.

4) Install 2 screws at the lower front edge corners of the Drafthood Bottom to secure the

Drafthood. These screws may need to be self drilling to screw into or through the existing

firebox.

5) Make sure that your unit is sitting at the correct height and that the Outer Shell is square

and centered in the install, fasten the Outer Shell to the existing firebox using self drilling and

tapping screws.

6) Locate and install the Surround Mounting Brackets Right and Left.

7) Using 2 screws provided, install the Control Box into a slot provided in the Surround

Mounting Bracket Left.

STEP #2: OUTER SHELL INSTALLATION

. Slide outer shell back into the existing firebox, ensure the vent slide

plate is properly engaged with the outer shell.

Move the outer shell back until the left and right flanges contact
the existing firebox.

Adjust the outer shell legs to the setting noted for your specific

installation. If these settings are not adhered to, the surround will not fit

correctly.

Attach the bent slide plate to the outer shell with one sheet metal

screw as shown in Figure 10.3. Refer to the applicable existing appli-

ance for correct measurements before securing outer shell in position.

. Ensure the unit is set at the correct height and the outer shell is square

and centered, fasten the outer shell to the existing firebox using self
tapping screws.

Ensure thermodiscs and thermodisc brackets are in

place.

. Install the firebox into the outer shell by sliding the

drafthood bottom onto the drafthood slide until you are
able to install 4 screws to secure the firebox. Use care
to avoid damaging the wire harness.

Note:

2 of the screws along with panel brackets to be

installed on the lower inside of the firebox.

. Unit is installed correctly when the flanges that se-

cure the firebox to the outer shell contact. Ensure the
unit is centered within the existing firebox, attach the
outer shell to the existing firebox using 4 x sheet metal
screws.

. Install 2 self tapping screws at the front edge corners of

the drafthood bottom to secure the drafthood.

. Install 1 x Phillips screw to fasten drafthood. Install 2 x

Phillips screws to secure left and right side of thermo-
disc bracket.

STEP #3: FIREBOX INSTALLATION

Diagram 10.3

Diagram 10.4

ZC box existing Unit

Measured from
Top of ZC box

Measured from side of

ZC box

EP28

8-7/16" (215mm)

1-7/16" (37mm)

28F - 28F2

7-3/16" (183mm)

1-1/2" (39mm)

Montigo 36SR

6-3/8" (162mm)

1-9/16" (40mm)

Firesong 220N

8-3/16" (208mm)

2-1/8" (54mm)

Содержание E18-LP














































































Результаты поиска

Содержание E18-LP

Отзывы:

Похожие инструкции для E18-LP

Бренды по названию

Популярные бренды

Regency E18-LP, Инструкция для владельца и по установке

Результаты поиска

Содержание E18-LP

Отзывы:

Похожие инструкции для E18-LP

Бренды по названию

Популярные бренды