Regency Cascades Series Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 48

background image

F2500 Regency Freestanding Woodstove

21

installation

Flue Baffle &
Secondary Air Tube
Installation

The flue baffle system located in the upper area of the firebox is removable
to make cleaning your chimney system easier. The baffles must be installed
prior to your first fire.

Smoke spillage and draft problems may occur if the

baffles are improperly positioned.

Check the position of the baffles on a

regular basis as they can be dislodged if too much fuel is forced into the firebox.

Freestanding Stove F2500

The unit arrives with the 2 baffles on the floor of the firebox.

1. Open the door and Remove stainless steel smoke deflector - See smoke

deflector instructions in this manual.

2. Remove the front secondary air tube with pliers as shown below.

4.

Tilt the left baffle up on top of the side channel and it will leave enough
room to position the right baffle in the same manner as Step 1) above.
Then reposition the left baffle flat on the air tubes.

Important:

push both baffles so they are tight against the side walls.

Front View

Front View

smoke

deflector

3. Slide the left baffle over the three remaining air tubes from the front and

then push it to the back.

Side View

5. Reverse Steps 1 and 2.

«
...
19
20
21
22
23
...
»

Содержание Cascades Series

















































Отзывы:

Нет отзывов

Похожие инструкции для Cascades Series

Бренд: L'Artistico Страницы: 152

Бренд: RAIS Страницы: 56

Бренд: RAIS Страницы: 81

Бренд: Breckwell Страницы: 40

Taurus Aqua 28/858

Бренд: Konigshutte Страницы: 36

Бренд: Country Hearth Страницы: 24

Бренд: Country Flame Страницы: 19

Бренд: Country Heart Страницы: 24

Бренд: COUNTRY FLAME TECHNOLOGIES Страницы: 37

THAMES TRAVEL BARGE 6910115

Бренд: Clarke Страницы: 24

Бренд: Carolina Cooker Страницы: 17

Бренд: Harman Home Heating Страницы: 5

Бренд: Style selections Страницы: 13

Hobbit 1901 SE eco

Бренд: Salamander Stoves Страницы: 12

HSP 6 Premium 521.08

Бренд: HAAS + SOHN Страницы: 19

Бренд: Harman Stove Company Страницы: 24

Бренд: Harman Stove Company Страницы: 25

Walltherm Vajolet

Бренд: Wallnofer Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды