Regency Alterra CI1150 Скачать руководство пользователя страница 9

Страница: 9 / 40

Regency CI1150 Wood Cast Insert

installation

Installing Your Insert

SAFETY NOTE:

The insert is very heavy and

will require two or three people to move it into

position. The insert can be made a little lighter

by removing the cast iron door by opening it and

lifting it off its hinges. Be sure to protect your

hearth extension with a heavy blanket or carpet

scrap during the installation.

NOTE:

You will be required to purchase either

the standard or offset 6" diameter (152mm)

flue adaptor that is best suited for the specific

installation.

List of Tools needed;

- Pull Rod (included with insert)

- 1/2” socket / ratchet

- 3/8 open face wrench

1. Install flex liner into existing chimney as per

liner manufacturer’s specifications. See

Diagram 1.

Pull Rod

10. Re-install the door if removed prior to installa-

tion.

NOTE: The pull rod should not be thrown

away. It should be kept if the stove

is ever needed to be removed from

the fireplace.

Flex Liner

Pull Rod In Place

Pull Rod

Diagram 1

Diagram 2

Diagram 3

Diagram 4

Diagram 5

Diagram 6

Flue Adaptor

Diagram 7

2. Install the required flue adaptor onto the end

of the flex liner. Secure the adaptor using 3

screws - 1 on the front (not shown in image),

left, and right side. See Diagram 2.

Alignment of the flue adaptor can be critical

during the install, it is recommended that the

flex liner be left as compressed as possible.

Before inserting the unit the adaptor should

hang, when level, slightly above the required

height.

3. Install the unit by first setting the rear of the

unit into the fireplace. See Diagram 3. En

sure that the unit is centered in the existing

fireplace and lined up with the flue adaptor.

4. Slide the unit back until the flue adaptor is

slightly engaged.

5. At this point it is recommended to level the

unit and ensure that the leveling bolts rest on

the surface of the fireplace. This will keep the

adaptor from binding as the unit is slid into

position.

6. Insert the provided pull rod through the hole

in the top center of the unit. Secure the

threaded end into the flue adaptor as shown

in Diagram 4. While sliding the unit into place

pull on the rod to ensure that the flue adaptor

is properly engaged. See Diagram 5.

7. Ensure that the unit is still level.

8. To complete the installation and to ensure a

secure fit and connection of the flue adaptor

to the insert, it is essential that the two bolts,

flat washers and lock washers (supplied with

packaged manual) be installed and tightened

using a 1/2" socket as shown in Diagram 6.

This prevents the possibility of creosote drip

and exhaust gas leakage.

9. Remove the pull rod from the top center of the

fireplace. See Diagram 7.

Содержание Alterra CI1150









































Результаты поиска

Содержание Alterra CI1150

Отзывы:

Похожие инструкции для Alterra CI1150

Бренды по названию

Популярные бренды

Regency Alterra CI1150, Инструкция для владельца и по установке

Результаты поиска

Содержание Alterra CI1150

Отзывы:

Похожие инструкции для Alterra CI1150

Бренды по названию

Популярные бренды