background image

6-7/8"

(173mm)

dia. Flue pipe

4" (102mm)

dia. flue pipe

Wall Thimble (2 pc)

Termination Cap

(Part# 946-523/P)

AstroCap

TM

spring
spacer

FPI Direct  Vent System (Flex)

Horizontal Terminations Only

This venting system, in combination with the P33 Direct Vent Gas 
Fireplace, have been tested and listed as a direct vent heater system by 
Warnock Hersey. The location of the termination cap must conform to the 
requirements in the Vent Terminal Locations diagram, see manual.

FPI Direct Vent (Flex) System Termination Kits include all the parts 
needed to install the P33 using a 

fl

 exible vent.

FPI Kit # 

Length  Contains:

#946-513

2 Feet

1)

 6-5/8” 

fl

 exible liner (Kit length)

2)

 4” 

fl

 exible liner (Kit length)

3)

  spring spacers (3)

4)

 thimble 

(2)

5)

 

AstroCap

 termination cap (1)

6)

 screws 

(12)

7)

  tube of Mill Pac (1)

8)

  plated screws (8)

9)

  S.S. screws #8 x 1-1/2” drill point, (4)

#946-515

4 Feet

#946-516

10 Feet

Notes: 
1)  Liner sections should be continuous without any joints or seams.
2)  Only Flex pipe purchased from Regency may be used for Flex 

installations.

3)  Horizontal sections must be supported every 3 feet.

If required by the external termination location the listed 
alternate termination caps may be used. 

Important

When installing Cabinet Mantels: the wall thimble must be secured 

fi

 rst and venting must be attached to unit before sliding into 

fi

 nal 

position.

Alternate Horizontal 

Termination Caps

Snorkel Terminations

Snorkel Terminations:

For installations requiring a vertical rise on the exterior of the building, 
14-inch and 36-inch tall Snorkel Terminations and the Riser Vents are 
available. Follow the same installation procedures as used for standard 
Horizontal Termination. NEVER install the snorkel upside down.

Min. 12"*
(305mm)

Dura-Vent

Snorkel

Riser Vent

Termination

Min. 6-1/4"*

(159mm)

Below Grade Snorkel Installation (Dura-Vent Only)

If the Snorkel Termination must be installed below grade, i.e. basement 
application, proper drainage must be provided to prevent water from 
entering the Snorkel Termination. Refer to Rigid Pipe Installation 
instructions for details. Do not attempt to enclose the Snorkel within the 
wall, or any other type of enclosure.

Min.

12"*

(305mm)

Adequate

drainage

Window

Well

Gravel

Dura-Vent

Snorkel

P33 Gas Fireplace

32

August 2008 Product Speci

fi

 cations Book

Gas Fir

eplaces

Gas Fireplaces

Содержание 510-994











Отзывы: