Regency Fireplace Products HRI3E-LP11 Скачать руководство пользователя страница 22

Страница: 22 / 64

22 |

LRI3E-11 / HRI3E-11 Direct Vent Gas Insert

installation

Detach the Flue Connector Plate from the unit by removing the

Connector Plate Screws and sliding the Flue Connector Plate forward
and off the unit.

NOTE:

Flue Plate Connector Gasket

must not be damaged or removed.

Care must be taken to ensure that this

gasket remains intact to prevent flue

leakage.

5. When the Flue Connector Plate is close to the front of the unit, engage

the Flue Connector Screws and carefully tighten the Flue Connector
Plate the final amount.

** Make sure the Rear Tab connects into the slot in the Flue Connector

Plate. Failure to do so will result in flue gas leakage and degrade the
operation of the unit ** (See diagram below of location.)

The Flue connection is complete when the Flue Connector Plate is fully

forward and the Rear Tabs are fully engaged.

6. Remove the Flue Connector Tool and store for future use.

2. Attach the Flue Liners onto the Flue Connector Plate using non RTV

type sealant, then fasten with 3 screws.

See the section in this manual on Venting installation.

3. Position the unit in front of the fireplace opening, start the Flue Connec-

tor Plate into the Flue Connector Plate Guides.

Flue Connector Slide Tool

Tab connected correctly

Flue Connector Plate

Connector Plate Screws

4. Use the Flue Connector Slide Tool to slowly pull the Flue Connector Plate

forward as you move the Insert rearward into the Fireplace Chase.

FLUE / VENT INSTALLATION

WARNING:

Failure to position the parts in accordance with these diagrams or failure
to use only parts specifically approved with this appliance may result in
property damage or personal injury.

Connecting the Vent Liners

Intake Liner

Exhaust Liner

Flue Connecter

Plate

Содержание HRI3E-LP11

































































Результаты поиска

Содержание HRI3E-LP11

Отзывы:

Похожие инструкции для HRI3E-LP11

Бренды по названию

Популярные бренды

Regency Fireplace Products HRI3E-LP11, Инструкция для владельца и по установке

Результаты поиска

Содержание HRI3E-LP11

Отзывы:

Похожие инструкции для HRI3E-LP11

Бренды по названию

Популярные бренды