Regency Fireplace Products F1105S, Инструкция для владельца и по установке

Страница: 59 / 72

Regency F1105/F3105 Freestanding Woodstove
|
23
operating instructions
purchase your replacement from an authorized
Regency dealer only.
Remove the door from the stove and remove
the glass retainer. Position the glass in the door,
make sure that the glass gasketing will properly
seal your unit, and replace the retainer, it should
rest on the gasket not the glass. Tighten securely,
but do not wrench down on the glass as this may
cause the glass to break.
OPTIONAL
ACCESSORIES
The pieces listed below can be purchased and
installed during the initial installation or added
on later.
Pedestal Ash Drawer Kit (850-100)
1) Remove the bricks from the floor of the
firebox.
2) If using ashdrawer, discard cover plate.
3) Remove the ash dump cover plates (one
inside the firebox and one on the underside
of the firebox) by removing the two nuts
and bolts holding the 2 plates together from
inside the firebox.
4) Push the ash plug into the hole inside the
firebox and replace all the bricks except
for the brick over the ash plug. See brick
diagrams.
5) Place the ash drawer lid inside the pedestal,
and the ash plug tool beside the lid, then
slide the ash drawer inside so it sits on top
of the lid.
Refer to the Ash Drawer Operating section.
Bottom Shield Ash Drawer Kit
(850-101 )
1) Remove the bricks from the floor of the
firebox.
2) Remove and discard the cover plate by
removing the two screws on the front of the
Bottom Shield.
3) Remove the ash dump cover plates (one
inside the firebox and one on the underside
of the firebox) by removing the two nuts
and bolts holding the 2 plates together from
inside the firebox.
4) Push the ash plug into the hole inside the
firebox and replace all the bricks except
for the brick over the ash plug. See brick
diagrams.
5) Place the ash plug tool beside the lid, then
slide the ash drawer inside.
BRICK INSTALLATION
Firebrick is included to extend the life of your
stove and radiate heat more evenly. Check to
see that all firebricks are in their correct posi -
tions and have not become misaligned during
shipping.
The "AD" brick in the drawings above is the
Pull - Open Push - Closed
brick covering the Ash Dump hole that is used
when the Ash Drawer Kit is installed (refer to
the Listed Components for Mobile Home Instal-
lation section).
DOOR HANDLE
Attach spring handle by rotating counter
clockwise onto rod. Ensure that the rod fits
into the entire length of the spring handle. See
Diagram below.
GLASS INSTALLATION
Your Regency stove is supplied with 5 mm
Neoceram ceramic glass that will withstand
the highest heat that your unit will produce. In
the event that you break your glass by impact,
Refer to the Ash Drawer Operating section.
Blower/Fan (846-515)
1) Remove the two screws from the top of the
fan housing.
2) Slide the fan up into the rear heat shield.
3) After aligning holes, secure the fan to the rear
heat shield using the two screws removed
earlier.
Note: The connection cord should not be
in contact with any hot surfaces.
Read the operating instructions for the fan
before using.
OPERATING
INSTRUCTIONS
With your unit now correctly installed and safety
inspected by your local authority, you are now
ready to start a fire. Before establishing your
first fire, it is important that you fully understand
the operation of your draft control.
WARNING: To build a fire in ignorance or
to disregard the information contained in
this section can cause serious permanent
damage to the unit and void your warranty!!
FIRST FIRE
When your installation is completed and in-
spected you are ready for your first fire.
1) Open control fully.
2) Open firebox door and build a small fire
using paper and dry kindling. Secure door
on the firebox and wait a few minutes for a
good updraft in the flue to establish the fire.
(Leaving the door slightly open will help your
WARNING
Fireplace Stoves equipped with doors
should be operated only with doors fully
closed. If doors are left partly open,
gas and flame may be drawn out of the
fireplace stove opening, creating risks
from both fire and smoke.
When operated with doors open the
manufacturer supplied screen must
be used.
DRAFT CONTROL
Both the primary and air wash drafts are control -
led by the control rod located on the left side
of the unit (when facing the unit). To increase
your draft - pull open, and to decrease - push
closed. All units have a secondary draft system
that continually allows combustion air to the
induction ports at the top of the firebox, just
below the flue baffle.
Important: If you are using room air for com-
bustion, make sure that the back cover plate
at the rear of the pedestal is not installed. The
cover plate must be installed on the unit if your
stove is located in a mobile home or if using
outside air.
How to Light & Maintain a Wood Stove Fire