KIT CONTENTS (See
Figure 1)
1 ea. Nova SIT LP Regulator Kit (A)
1 ea. #49 LP main burner orifice (39,000 BTU) (B)
1 ea. #52 LP main burner orifice (31,000 BTU) (C)
1 ea. Sticker “Epic LP 39” if LP orifice was #49
1 ea. Sticker “Epic LP 31” if LP orifice was #52
1 ea. Instruction Sheet
TOOLS NEEDED (See
Figure 2)
5/32” Allen Wrench or T-Handle Wrench
1/8” Allen Wrench or T-Handle Wrench
Torx Bit (T20 with 1/4” shank and center hole)
1/2” Open End Wrench
7/16” Open End Wrench
EpIC™ GaS CONvErSION INSTruCTIONS NG TO Lp
CaT. NO. 75352, MODEL EpIC-CK-NG TO Lp
INSTaLLaTION INSTruCTIONS FOr CONvErTING FrOM NaTuraL GaS (NG) TO
prOpaNE GaS (Lp) FOr uSE wITh ThE EpIC DIrECT vENT GaS STOvE
775244M
rev. C, 12/2013
HEARTH PRODUCTS
KITS AND ACCESSORIES
warNING
This conversion kit shall be installed by a qualified
service agency in accordance with the manufacturer's
instructions and all applicable codes and requirements
of the authority having jurisdiction. If the information
in these instructions is not followed exactly, a fire,
explosion or production of carbon monoxide may result
causing property damage, personal injury or loss of
life. The qualified service agency performing this
installation is responsible for the proper installation of
this kit and assumes responsibility for this conversion.
The installation is not proper and complete until the
operation of the converted appliance is checked as
specified in the manufacturers instructions supplied
with the kit.
IMpOrTaNT LE CaNaDa SEuLEMENT
La conversion devra être effectuée conformément
aux recommandations des autorités provinciales
ayant juridiction et conformément aux exigences
du code d'installation CaN/CGa B149.1.
IMpOrTaNT CaNaDa
The conversion shall be carried out in accordance with
the requirements of the provincial authorities having
jurisdiction and in accordance with the requirements
of the CaN/CGa B149.1 Installation code.
avErTISSEMENT
Cet équipement de conversion sera installé par une
agence qualifiée de service conformément aux instruc-
tions du fabricant et toutes exigences et codes applica-
bles de l'autorisés avoir la juridiction. Si l'information
dans cette instruction n'est pas suivie exactement, un
feu, explosion ou production de protoxyde de carbone
peut résulter le dommages causer de propriété, perte
ou blessure personnelle de vie. L'agence qualifiée de
service est esponsable de l'installation propre de cet
équipment. L'installation n'est pas propre et compléte
jusqu'à l'opération de l'appareil converti est chéque
suivant les critères établis dans les instructions de
propriétaire provisionnées avec l'équipement.
IMpOrTaNT
The burner orifices provided in this kit are only for
use at elevations of 0 to 2,000 feet (610 M) in the
uSa and 0 to 4,500 feet (0-1372 M) in Canada. at
higher elevations the BTu input must be de-rated
by 4% for every 1,000 feet (305 M) to maintain
the proper ratio of gas to air. If the installer must
convert the unit to adjust for varying altitudes, a
deration information sticker must be filled out by the
installer and adhered to the appliance at the time
of the conversion. Contact your local gas supplier
for deration requirements for your area.
A
C
B
Fig. 2
Figure 1 - Kit Contents
Figure 2 - Tools Needed
1
f i r e - p a r t s . c o m
