Regency Fireplace Products Energy U31, Инструкция для владельца и по установке

Страница: 36 / 48

36 | Regency U31-10 Gas Fireplace Insert
|
36
maintenance
Top view of pilot flame
Correct flame pattern has four strong blue
flames: 1 flowing around the thermopile and
thermocouple and 1 reaching towards the
rear burner and 1 toward the front(it does
not have to be touching the burner).
Top view of pilot flame
Incorrect flame pattern will have small,
probably yellow flames, not coming into
proper contact with the rear burner or
thermopile.
CAUTION: ANY SAFETY SCREEN
OR GUARD REMOVED FOR
SERVICING AN APPLIANCE
MUST BE REPLACED PRIOR TO
OPERATING THE APPLIANCE.
WARNING: DO NOT OPERATE
APPLIANCE WITH THE GLASS
FRONT REMOVED, CRACKED OR
BROKEN. REPLACEMENT OF THE
GLASS SHOULD BE DONE BY A
LICENSED OR QUALIFIED
SERVICE PERSON.
MAINTENANCE
INSTRUCTIONS
1) Always turn the gas valve to off before cleaning.
For relighting, refer to lighting instructions. Keep
the burner and control compartment clean by
brushing and vacuuming at least once a year.
When cleaning the logs, use a clean soft paint
brush as the logs are fragile and easily damaged.
2) Clean (never when unit is hot) appliance, door
and louvers with a damp cloth. Never use an
abrasive cleaner. The gold louvers (and optional
gold door) may be scratched if abrasives are
used to clean them.
The heater is finished in a heat resistant paint
and should only be refinished with heat resistant
paint (not with wall paint). FPI uses StoveBrite
Paint - Metallic Black #6309.
3) Make a periodic check of burner for proper
position and condition. Visually check the
flame of the burner periodically, making sure
the flames are steady; not lifting or floating.
If there is a problem, call a qualified service
person.
4) The appliance and venting system must be
inspected before use, and at least annually,
by a qualified field service person, to ensure
that the flow of combustion and ventilation air
is not obstructed.
During the annual service call, the burners
should be removed from the burner tray and
cleaned. Replace the embers but do not block
the pilot.
5) Keep the area near the appliance clear and
free from combustible materials, gasoline and
other flammable vapours and liquids.
6) Each time the appliance is lit, it may cause
condensation and fog the glass. This conden-
sation and fog is normal and will disappear in
a few minutes as the glass heats up.
Never operate the appliance without
the glass properly secured in place, with
broken glass or with the door open.
7)
Verify proper operation after servicing.
8) Do not use this appliance if any part has been
under water. Immediately call a qualified ser -
vice technician to inspect the appliance and to
replace any part of the control system and any
gas control which has been under water.
C L O T H I N G O R O T H E R
FLAMMABLE MATERIAL SHOULD
NOT BE PLACED ON OR NEAR
THE APPLIANCE.
GLASS GASKET
If the glass gasket requires replacement use 7/8"
flat glass gasket (Part # 936-243) for the Bay Front
and for the Flush Front.
DOOR GLASS
REPLACEMENT
Your Regency insert is supplied with high
temperature, 5 mm Neoceram ceramic glass that
will withstand the highest heat that your unit will
produce. In the event that you break your glass
by impact, purchase your replacement from an
authorized FPI dealer only, and follow our step-
by-step instructions for replacement.
Flush Glass Replacement
Slide old glass out of the side frames and replace
with new glass.
WARNING: CHILDREN AND
ADULTS SHOULD BE ALERTED
TO THE HAZARDS OF HIGH
SURFACE TEMPERATURE
AND SHOULD STAY AWAY TO
AVOID BURNS OR CLOTHING
IGNITION. YOUNG CHILDREN
SHOULD BE CAREFULLY
SUPERVISED WHEN THEY ARE
IN THE SAME ROOM AS THE
APPLIANCE.
LOG REPLACEMENT
The unit should never be used with broken logs.
Turn off the gas valve and allow the unit to cool
before opening door to carefully remove the logs.
The pilot light generates enough heat to burn
someone. If for any reason a log should need
replacement, you must use the proper replacement
log. The position of these logs must be as shown
in the diagram under Log Installation.
NOTE: Improper positioning of logs may
create carbon build-up and will alter
the unit’s performance which is not
covered under warranty.
If you have an incorrect flame pattern, contact your
FPI dealer for further instructions.