manualshive.com logo in svg

Regency Fireplace Products CI2600, Инструкция для владельца и по установке

Поделиться
Скачать
Regency Fireplace Products CI2600 Скачать руководство пользователя страница 31

 

 

CI2600/HI400 |  wood insert

 

 

|

 

31

operating instructions

OPTIONAL DIGITAL CATALYTIC COMBUSTOR MONITOR 

NOTE:

 1/4" drill bit required for this installation.

The CI2600/HI400 is equipped with a provision to accept a catalytic tempera-
ture monitoring device. Please follow instructions below for the installation of 
the probe. Follow the user instructions of the catalytic monitoring device for 
product set up and details.

1. 

Remove all packaging from the unit

 

2. 

 Locate the precut square on the top of the unit. Lift up the metal square to 

90

0

 with a flat head screwdriver.

3.  

Locate the 7/16’’ bolt below the metal. Use a 7/16’’ socket and remove the bolt.  

 

   Remove 7/16’’ bolt.

   Install temperature probe

Drill hole with 1/4" drill bit

  Probe

  Device

4. 

 Use a ¼’’ drill bit and drill through the hole. Make sure the drill bit size is 

correct to ensure a air tight seal when the probe is installed.

5.  

Take your temperature probe and measure from end 3’’ and make a mark. 

Insert the temperature probe to the mark

.

6.  

Complete the installation of the CI2600/HI400. Ensure temperature probe 

wire is routed behind the faceplate and to the left side of the unit. Plug the 

in the monitoring device.

   

Содержание CI2600













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды