manualshive.com logo in svg

Regency Fireplace Products CI2600, Инструкция для владельца и по установке

Поделиться
Скачать
Regency Fireplace Products CI2600 Скачать руководство пользователя страница 24

CI2600/HI400 |  wood insert

24

 | 

installation

OPTIONAL FAN/BLOWER INSTALLATION 

919-320a

04/1514

OPTIONAL FAN/BLOWER INSTALLATION

The fan should only be installed once the unit is in 

place in order to prevent any damage to the fan. 

1.   

 Remove 2- 5/16" screws from locations 

shown below—set aside for installation.

Installer:

   Please record unit serial number here before installing blower—serial number will not be visible after blower 

is installed.

Serial No.

______________________________

2.

    Slide the fan cassette fully into position.

Remove 2 screws from locations shown 

Secure fan with 2 screws removed in Step 1

Secure preset strain relief

Tuck cord to right side of faceplate

Line up fan cassette with screw holes.

7.

  Remove the dummy plug from the faceplate 

being  installed,  by  removing  the  2  screws 
along with washers and nuts. Discard dummy 
plug,  but  keep  hardware.  Install  fan  switch 
assembly  with  2  screws,  or  use  washers 
and  nuts  for  Cast  Faceplate  to  lower  fas-
cia  before  sliding  faceplate  into  position.

8.

  Tuck Power Cord to the bottom right hand side 

of the faceplate as shown.

 

Do not turn fan ON until your insert has reached 

operating temperature or at least 30 minutes 

after starting fi re.

Fan switch assembly

5.

   Remove 7/16" bolts from position shown 

below.

**See specifi c faceplate installation instructions 

for detailed instructions of fan switch assembly.

6

.  Align preset strain relief bracket to bottom 

right corner of the faceplate, secure with 7/16" 

bolt removed in Step 5.

3.

    Align screw holes on fan harness bracket 

with holes in fan cassette mounting bracket 

on right and left sides. 

4.

   Secure using the two (2) 5/16" screws re-

moved from Step 1.

1

CI2600

Содержание CI2600













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды