manualshive.com logo in svg

Regency Fireplace Products CI2600, Инструкция для владельца и по установке

Поделиться
Скачать
Regency Fireplace Products CI2600 Скачать руководство пользователя страница 2

CI2600/HI400 |  wood insert

2

 | 

http://oee.nrcan.gc.ca/residential/personal/retrofit-homes/retrofit-qualify-grant.cfm

Thank-you for purchasing a 

REGENCY FIREPLACE PRODUCT.

The pride of workmanship that goes into each of our products will give you years of trouble-free enjoyment.  Should you have 
any questions about your product that are not covered in this manual, please contact the 

REGENCY DEALER 

in your area.

Keep those 

REGENCY FIRES

 burning. 

SAFETY NOTE:

 If this wood stove is not properly installed, a house fire may result.  For your safety, follow the installation 

instructions, contact local building, fire officials, or authority having jurisdiction about restrictions and installation inspection 
requirements in your area. 
 

The following statements are required by the Environmental Protection Agency:

"

This manual describes the installation and operation of the Regency CI2600/HI400 catalytic equipped heater. This heater 

meets the U.S. ENVIRONMENTAL PROTECTION AGENCY’s emission limits for wood heaters built on or after July 1 1990. 
Under specific test conditions this heater has been shown to deliver heat at rates ranging from 

15165 BTU/hr to 27535 BTU/hr

.

"This wood heater contains a catalytic combustor, which needs periodic inspection and replacement for proper operation. It 
is against the law to operate this wood heater in a manner inconsistent with operating instructions in this manual, or if the 
catalytic element is deactivated or removed."

CAUTION

:  BURN UNTREATED WOOD ONLY. OTHER MATERIALS SUCH AS WOOD PRESERVATIVES, METAL FOILS, 

COAL, PLASTIC,GARBAGE, SULPHUR OR OIL MAY DAMAGE THE CATALYST

"This heater is designed to burn natural wood only. Higher efficiencies and lower emissions generally result when burning air 
dried seasoned hardwoods, as compared to softwoods or to green or freshly cut hardwoods."

DO NOT BURN

: 

 

•  Treated wood

 

•  Coal

 

•  Garbage

 

•  Cardboard

 

•  Solvents

 

•  Colored Paper

 

•  Trash

The authority having jurisdiction (such as Municipal Building Department, Fire Department, Fire Prevention Bureau, 
etc.) should be consulted before installation to determine the need to obtain a permit. 

This unit must be connected to either a listed factory built chimney suitable for use with solid fuels and conforming to, 
UL1777,ULCS635 and ULCS640, or code approved masonry chimney with flue liner.
CI2600/HI400 is tested and certified to ULCS-628-93 and UL1482-2011.

SAVE THESE INSTRUCTIONS

Содержание CI2600













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды