Regal Smartvalve 7001 Скачать руководство пользователя страница 3

1.   Read these and all related instructions thoroughly and follow 

     them carefully.  

2.   Make certain all required safety equipment is in place and     

     operational.  

3.   Whether it is required or not, a gas mask (DEMAND TYPE AIR 

     PACK) should be available in the immediate area of the gas       
     feed equipment and all operating personnel should be properly 
     trained in its use. OPERATORS SHOULD NOT ENTER             
     AREAS WHERE CHLORINE EXISTS, UNESCORTED.  

4.   Chlorine and Sulfur Dioxide gas or the fumes from Chlorine             

     and Sulfur Dioxide solutions can be lethal  in large enough                   
     doses. Always have a coworker observe from a safe location      

      when you are working on any part or component of the gas feed 

     system.  

5.   Avoid breathing the gas fumes of Chlorine and Sulfur Dioxide         

     solutions and AVOID contact with your skin. Work only in a      

     well ventilated area.  

6.   Before working on the gas feed system, make certain that the 

     cylinder/container/manifold valve(s) are shut off. If the        
     cylinder/container/manifold valve(s) seem to be shut off, open 
     them one quarter turn, and immediately close them again to       
     make certain they are not frozen in the open position. If you      
     cannot turn the valve(s) in either direction, ALWAYS ASSUME 
     THEY ARE OPEN, and call your chemical supplier.  

7.   Do not use wrenches larger than the standard cylinder/container 

     wrench (approximately 8˝ long) and DO NOT hit the wrench       
     with a heavy object to open or close the valve.  

8.   Do not reuse lead gaskets. They may not seal properly thereby 

     permitting the release of gas.  

9.   Use only lead gaskets. Other types may contract with                

     temperature variations resulting in the escape of gas.  

10. Check for gas leaks every time the vacuum regulator(s) are  
     connected or remounted onto the cylinder/container/manifold 
     valve.  

11. The rate valve IS NOT a shut-off valve. To shut off the gas  
      supply, CLOSE THE CYLINDER/CONTAINER/MANIFOLD 

      VALVE(S).

 

PRECAUTIONS FOR PERSONAL AND SYSTEM PROTECTION

IMPORTANT: 

 

Please mail or fax this registration form 

 to establish your warranty. 

REGAL REGISTRATION CARD

IMPORTANT: 

To further establish your warranty and to enable us to contact you should the

 

need arise, please fill out this card and return it promptly. Please do it now. Thank you.

 

 

Chlorinators Incorporated, Stuart, FL is the only authorized Warranty Repair facility for

 

REGAL 

GAS DETECTOR

S/SMARTVALVES.

 

 

PLEASE PRINT, THANK YOU

 

 

Gas Detector/SMARTVALVE Serial No.(s)*  1._________________ 2._________________

 

             

 

                 

 

                                   

*Serial No. plate located inside unit on the right

 

 

Purchased From

  ________________________________________________________

__

 

Your Name

  ____________________________________________ Title_______________

 

Organizatio

n

 ______________________________________________________________

 

Mailing Addres

s

 _____

_______

_______________________________________________

 

City _____________________________________ State

  _____________ 

Zip ___________

 

Phone

 

(__________) _____________________________________  Ext. ________

____

REGAL Registration Card

3

Содержание Smartvalve 7001





























Отзывы: