REFU REFUsol 48K-UL Скачать руководство пользователя страница 53

Страница: 53 / 72

REFU Elektronik GmbH

REFUsol 48K-UL

Error
Code

Text

Description

Action

90020

Initialisation C1

Initialisation has failed.

Restart inverter. If this does not
rectify the error, contact Service.

90021

Initialisation C0

90024

SR parameter
error

Error in parameter initialisation. The
device has been permanently shut
down.

Please contact Service.

90029

Update fault

Update failed

The update has failed. Contact
Service.

9002A

Keep Alive

Internal communication monitoring
has determined a fault.

Please contact Service.

9002B Update End

Update successful notification.

An update was successfully
completed. The device will resume
normal operation.

9002C AntiIslandPhase

Shift

Islanding of the connected grid
section has been detected

Wait for the grid to become stable
again

9002D AntiIslandRocof

9002F

FFS is read-only Internal data can't be written

anymore.

Please contact Service.

90030

DC share too
high

The measured DC-Part in AC current
exceed the defined limit.

90031

ETH link lost

The Ethernet cable has been
removed

Check the Ethernet cable on the
device and the receiver (router,
switch) for a correct fit. If the
cables are correctly connected and
should the notification still be
there, please contact Service.

90032

Restart

The system has been rebooted.

Should these notifications occur
repeatedly during daily operation,
please contact Service.

90050

AC condition

AC switch on condition not fulfilled

Wait until the network is stable

90051

DC condition

DC switch on condition not fulfilled

Wait until the solar voltage is high
enough

90052

User lock active The inverter can't connect to the grid,

as the User-lock has been set.

Deactivate user lock

90053

Communication
SR

Internal communication problems

Fault is independently resolved
after a few minutes. If not, switch
device off and on again. If this does

Содержание REFUsol 48K-UL









































































Результаты поиска

Содержание REFUsol 48K-UL

Отзывы:

Похожие инструкции для REFUsol 48K-UL

Бренды по названию

Популярные бренды

REFU REFUsol 48K-UL, Инструкция по установке и эксплуатации

Результаты поиска

Содержание REFUsol 48K-UL

Отзывы:

Похожие инструкции для REFUsol 48K-UL

Бренды по названию

Популярные бренды