background image

7

7.  Battery and Rechargeable Battery Notes

•  Keep batteries/rechargeable batteries out of the reach of children.
•  Do not leave any batteries/rechargeable batteries lying around openly. There is a risk of batteries being swallowed 

by children or pets. If swallowed, consult a doctor immediately!

•  Batteries/rechargeable batteries must never be short-circuited, disassembled or thrown into fire. There is a danger 

of explosion!

•  Leaking or damaged batteries/rechargeable batteries can cause chemical burns to skin. Wear suitable protective 

gloves when handling them. 

•  Do not recharge normal batteries. There is a risk of fire and explosion! Charge only rechargeable batteries intended 

for this; use suitable chargers.

•  Always observe correct polarity (po and negative/-) when inserting the batteries/rechargeable batteries. 
•  If the device is not used for an extended period of time (e.g. storage), remove the inserted batteries/rechargeable 

batteries from the remote control and the car to avoid damage from leaking batteries/rechargeable batteries.

•  Recharge the rechargeable batteries about every 3 months. Otherwise, so-called deep discharge may result, ren

-

dering the rechargeable batteries useless.

•  Always replace the entire set of batteries or rechargeable batteries. Never mix fully charged batteries/rechargeable 

batteries with partially discharged ones. Always use batteries or rechargeable batteries of the same type and manu-

facturer.

•  Never mix batteries and rechargeable batteries! 
•  For reasons of operational safety, only use batteries and rechargeable batteries for the remote control transmitter.

8.  Charging Rechargeable Batteries

If you use NiMH rechargeable batteries for power supply of the receiver, they are usually flat at delivery and must be 

charged.

  Please note: 

 

Before a NiMH rechargeable battery reaches maximum capacity, several complete discharge and charge 

cycles are necessary. 

 

Always discharge the rechargeable battery at regular intervals, since charging a "half-full" rechargeable bat-

tery several times can cause a so-called lazy battery effect. This means that the rechargeable battery loses 

capacity. It no longer provides all of its stored energy, and the operating time of the model is reduced.

 

If you use several rechargeable batteries, purchasing a high-quality charger may be worthwhile. Such a 

charger usually has a quick-charging feature.

Содержание HT-5

































Отзывы: