REED CM-9930 Скачать руководство пользователя страница 3

reedinstruments

www

com

3

Safety

To ensure safe operation and service of this meter, follow these 

 

instructions:
•  Ensure that the DC 9V battery is connected to its snap terminal with the 

right polarity and correctly placed in the battery compartment 

•  Place the Red and Black test leads into the proper input terminal before 

taking any measurements

•  Remove one of the test leads from the circuit before changing the 

 

measurement range

•  Be sure to release the data hold button before taking a new 

 

measurement otherwise the display reading will freeze permanently

•  Do not allow the input terminal to exceed the maximum rated voltage
•  Always switch the function rotary switch to the OFF position when the 

instrument is not operation

•  Remove the battery if the instrument will not be used for an extended 

period of time

•  Even though the ohm and capacitance ranges have an overload 

 

protection circuit, it is prohibited to apply any voltage to the input 

 

terminal when taking measurements

•  The water resistance casing is applicable for the front panel on the 

instrument only. Do not throw the instrument into water or the meter will 
be damaged permanently

•  When changing the test leads you should only use the replacements 

that have the approval of CAT III-1000V

•  Only use a dry cloth to clean the plastic case

Caution: Risk of electric shock.

Caution: Do not apply overload voltage or current to the input

 

terminal. Always remove test leads before opening 

 

 

the battery cover.

Содержание CM-9930

















Отзывы: