Redpath Statesman 2.43m x 3.65m Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 27

Redpath Statesman 2.43m x 3.65m Скачать руководство пользователя страница 5

5

REDPATH POLYCARBONATE GREENHOUSE BASE DIMENSIONS

(Materials not supplied)

Base material may be: Timber, Brick, Block, or Concrete

(Dimensions shown are to the exterior edges)

The dimensions given below are for the base & ground anchoring system of your Polycarb  house. You will need to supply the
materials & construct these using Concrete, Brick or Timber.  Ensure that dimensions A & B are not exceeded!  -  As these are
precise outside measurements enabling the aluminum base cill of the Polycarbhouse (supplied) to overhang the edges of your
base.  Also ensure that the base is square by measuring across the corners (C) in both directions. Only when this measurement is
equal is the base square!
Check the level using a builder’s spirit level – in directions (A), (B) & (C) The building & its Polycarbonate cladding relies on the
buildings base being level in all directions.  The height of the base is typically up to 150mm above ground level, with a portion of
the base being below ground level. If using Timber for the base, the base will need to be secured to the ground with pegs spaced
at a width & depth to suit your chosen sites wind exposure & ground conditions.

MODEL: Nominal frame size

A (actual base size width)

B (actual base size length)

C (actual diagonal – check)

Statesman 2.43m x 3.65m

2570mm

3804mm

4591mm

Statesman 2.43m x 4.87m

2570mm

5040mm

5657mm

Note: Please check with your local council whether a building permit is required for

your Polycarbhouse before construction commences

«
...
3
4
5
6
7
...
»

Содержание Statesman 2.43m x 3.65m




























Отзывы:

Нет отзывов