Redi Controls RuptureSeal RS-2 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 18

Redi Controls RuptureSeal RS-2 Скачать руководство пользователя страница 16

16

Appendix “C” (continued)

Variations in RS-2 valve mountings to a chiller’s rupture disk.

The

RuptureSeal

™ is designed to be installed directly into the outer flange of the chiller’s rupture

disk,

WITHOUT THE USE OF A 45º or 90º ELBOW TURN BETWEEN THE RUPTURE DISK AND

THE RuptureSeal™,

or any piping extensions. It is highly recommended that the

RuptureSeal

™ be

mounted in one of the “Preferred” ways illustrated below.

However, if you have a situation where the

RuptureSeal

™ cannot be mounted in one of the

“Preferred” arrangements illustrated below, then you can use a straight extension pipe between the
rupture disk and the

RuptureSeal

™, of

UP TO A MAXIMUM OF FOURTEEN INCHES (14”) IN

LENGTH

(see sample illustrations below).

If a typical installation or an installation with a straight pipe extension is not possible, you may have to
modify the chiller by putting a 45º or 90º elbow

BEFORE THE RUPTURE DISK

. The

RuptureSeal

™

valve can then be mounted to the outer rupture disk flange to assure that, if there is a rupture, all of
the carbon fragments of the disk will be projected straight into the

RuptureSeal

™ carbon fragment

collection trap.

Chiller

Chiller

Chiller

Chiller

Preferred Installation - 1

Preferred Installation - 2

Alternate - 1 (with 14" pipe extension)

Alternate - 2 (with 14" pipe extension)

Caution:

DO NOT ATTEMPT TO MOUNT THE

RuptureSeal™

UTILIZING A 45º or 90º

ELBOW TURN AFTER THE RUPUTRE DISK, OR UTILIZING BOTH A 45º or 90º ELBOW
TURN AND A PIPE EXTENSION BETWEEN THE CHILLER’S RUPTURE DISK AND THE

RuptureSeal™.

In the event of a rupture, this could inhibit the normal functioning of the

carbon fragment collection trap and thereby cause the v alve not to work properly. (See
illustrations of the two types of prohibited installations on the left below.

Chiller

Chiller

Typical Installation on

chillers using R-123

Alternate - 3

Installation utilizing a 90 degree

elbow and a 14" pipe extension

after the chiller's rupture disk

(NOT AUTHORIZED)

Installation utilizing a 90

degree elbow turan after
the chiller's rupture disk

(NOT AUTHORIZED)

Chiller

Chiller

Note: Double check valve
output is piped to line from
valve drain hole to drip leg

Note: Check Valve
mounted in
vertical position

«
...
14
15
16
17
18
»

Содержание RuptureSeal RS-2



















Отзывы:

Нет отзывов