red lion RJS-100-PREM Скачать руководство пользователя страница 2

This is the safety alert symbol. When you see this   symbol on your pump or in this manual, look for one of the following signal words and be 
alert to the potential for personal injury or property damage if ignored:

warns about hazards that will cause serious personal injury, death or major property damage if ignored.

warns about hazards that can cause serious personal injury, death or major property damage if ignored.

warns about hazards that will or can cause minor personal injury or major property damage if ignored.

indicates special instructions which are important but not related to hazards. Carefully read and follow all safety instructions 

in this manual and on pump.

DANGER

!

WARNING

!

CAUTION

!

NOTICE

!

BEFORE OPERATING OR INSTALLING THIS PUMP, READ THIS MANUAL AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS. 

WARNING

!

READ AND FOLLOW ALL SAFETY INSTRUCTIONS.

WARNING

!

ELECTRICAL PRECAUTIONS -

 All wiring, electrical connections, and system grounding must comply with the  

National Electrical Code (NEC) and with any local codes and ordinances. Employ a licensed electrician.

WARNING

!

FOR DUAL VOLTAGE MOTORS (115/230 V)

 - Voltage change instructions are located in this manual.

NOTICE

!

 The motor voltage is factory set at 230 V.

WARNING

!

RISK OF ELECTRIC SHOCK

 

•  Have an electrician provide electrical power to motor.
•  We recommend that a separate circuit be lead from the home electrical distribution panel, properly protected with a fuse  

or a circuit breaker.

•  A ground fault interrupter (GFI) protected circuit is also recommended for use with any electrical device operating near water.
•  For recommended cable size see Table 2.
•  Motor must be grounded and terminal cover in place to reduce electrical shock hazard.
•  Keep motor operating area as dry as possible.
•  Always disconnect power before servicing.
•  Not investigated for use in swimming pool areas.

WARNING

!

75 PSI PRESSURE RELIEF VALVE RECOMMENDED

This pump is capable of producing high pressure. Installing a 75 psi pressure relief valve is highly recommended.

BEFORE GETTING STARTED

Read and follow safety instructions. Refer to product data plate(s) for additional operating instructions and specifications.

W A R N I N G

W A R N I N G

2

Содержание RJS-100-PREM

















Отзывы: