background image

www.ReadyLIFT.com  

-

  Phone: (877) 759

-

9991

 

 3

 

69

-

41200

-

IM

-

AA

 

Due to payload options and initial ride height variances, the amount of lift is a base figure. Final ride height 
dimensions may vary in accordance to original vehicle ride height. Always measure the vehicle ride height 
prior to beginning installation.

 

 

A lifted vehicle may have different headlight aim performance.

 

 ReadyLIFT recommends marking and 

recording the headlight beam position before kit installation and then adjusting, if necessary, the headlamps 
to the same height settings after kit installation.

 

 Set the vehicle on a level surface 10' to 

15’ 

from a solid wall 

or garage door.

 

 (This is a general distance with some manufacturers requiring different distances.)

 

 Note the 

top height of the low beam's bright spot, the top of the most intense part of the beam, for driver and 
passenger side.

 

 Height may vary from side to side.

 

 Repeat this procedure and adjust after lift kit is 

installed.

 

 Adjust if the aim is off by turning the adjusters gradually (a quarter of a turn) and looking to see 

where the new alignment falls.

 

 It may be easier to block one headlamp while adjusting the other.

 

 Consult 

the owner operation manual for procedures to adjust headlights 

-

 many automakers offer headlight aiming 

specs.

 

 Some states have their own specifications when it comes to headlight aim, so it

s best to follow those 

rules when aligning headlights.

 

 

 

SAEJ2492 Warning

 

 

 

By installing this product, you acknowledge that the suspension of this vehicle has been modified. As a result, 
this vehicle may handle differently than that of factory equipped vehicles. As with any vehicle, extreme care 
must be used to prevent loss of control or roll

-

over during sharp turns or abrupt maneuvers. Always wear 

seat belts, and drive safely, recognizing that reduced speeds and specialized driving techniques may be 
required. Failure to drive this vehicle safely may result in serious injury or death. Do not drive this vehicle 
unless you are familiar with its unique handling characteristics and are confident of your ability to maintain 
control under all driving conditions. Some modifications (and combinations of modifications) are not 
recommended and may not be permitted in your state. Consult your owner

s manual, the instructions 

accompanying this product, and state laws before undertaking these modifications. You are responsible for 
the legality and safety of the vehicle you modify using these components.

 

Содержание 69-41200
















Отзывы: