background image

EN

25

 

2 .11  P1 primary pump operation

The P1 primary circulation pump (class A inverter) is started 

when a request for hot water (reading of T3 positioned in the 

ACS tank) or from the system (reading of T1 positioned in the 

separator) is received. It may be managed using three algo-

rithms which can be set using the specific PMS parameter of the 

controller:

According to the default setting, the pump operates in nor “on 

demand” in cooling or heating when the pump is active only 

when requested by the temperature regulator (the circulator 

starts 20 seconds before the other two outputs and is switched 

off with a two minute delay) and if the TA selection, “hot water 

only”, is open the pump runs the cycles only when requested by 

the regulator according to the reading of hot water sensor T3.

Other operating mode are “continuous” (in which the pump op-

erates uninterruptedly for as long as the instrument is active) or 

“energy saving” (in which in addition to the normal request of 

the regulator it runs cycles consisting of 2 minutes ON and 15 

minutes OFF if the temperature regulator condition is satisfied). 

The modes can be activated by means of the specific parameters 

by Technical Service.

If the boiler function (CAL) is enabled is enabled and the AUX-

ILIARY HEATER is switched to the heating pump and the device 

is set in standby. The “CAL” prompt appears on the display and 

is only the SAN output is activated, always controlled by the T3 

sensor.

The pump output is always activated in case of antifreeze alarm 

detected by the sensors T2 or T3.

II

I

III

Min.

Содержание PDC FLOOR 12T

































































Отзывы: