RDZ PDC FLOOR 12T Скачать руководство пользователя

Страница: 50 / 64

F08

External temperature sensor TO disconnected, interrupted or

short-circuited.

Check sensor and replace it, if needed.

F10

Adjustment signal connection from controller disconnected,

interrupted or short-circuited.

Check connection of terminals 1 and 2 of INN-PDC-02 controller to

CN104 connector of board CR-UXRP71B.

F12

Compressor intake sensor TS disconnected, interrupted or

short-circuited.

Check sensor and replace it, if needed.

F29

Indoor unit EEprom problem.

Disconnect and reconnect power to the device and check correct

operation.

Replace and reprogram the CR-UXRP71B board.

F31

External unit EEprom problem.

Disconnect and reconnect power to the device and check correct

operation.

Replace and reprogram the external unit board.

L02

Parameter incompatibly between internal and external unit.

Check the automatic settings of the address again (paragraph

3.3.3Automatic address settingp<?>).

Contact RDZ S.p.A. Service to run programming again.

L08

No setting in the indoor unit.

L09

No setting in the indoor unit.

L10

No setting in the external unit.

L13

Incorrect settings of parameters in the indoor unit.

E01

Automatic setting of address has not been completed.

Wiring between internal and external unit are cut or not con-

nected correctly.

Check the connection of terminals 1 and 2 of the indoor unit

to the external unit (a shielded double-core cable, minimum

cross-section area 0.35 mm² kept separate from the electric power

cables).

Check the external unit control panel connection.

Check the automatic settings of the address again (paragraph

3.3.3Automatic address settingp<?>).

E03

Signal reception error by indoor unit.

E04

E06

Problems of communication between external and indoor

units.

E07

E15

Power of indoor unit lower than external unit.

Check device size and reconfigure the indoor unit.

E16

Power of external unit lower than indoor unit.

Check device size and reconfigure the indoor unit.

E20

Automatic addressing procedure interrupted.

Check the connection of terminals 1 and 2 of the indoor unit

to the external unit (a shielded double-core cable, minimum

cross-section area 0.35 mm² kept separate from the electric power

cables).

Check the external unit control panel connection.

Check the automatic settings of the address again (paragraph

3.3.3Automatic address settingp<?>).

E31

Problems of communication between external and indoor

units.

Содержание PDC FLOOR 12T

































































Результаты поиска

Содержание PDC FLOOR 12T

Отзывы:

Похожие инструкции для PDC FLOOR 12T

Бренды по названию

Популярные бренды

RDZ PDC FLOOR 12T, Руководство по установке

Результаты поиска

Содержание PDC FLOOR 12T

Отзывы:

Похожие инструкции для PDC FLOOR 12T

Бренды по названию

Популярные бренды