RCA Professional series Скачать руководство пользователя страница 7

Страница: 7 / 48

Supplied Accessories

Please check that you have received the
following supplied accessories:

• AM loop antenna

• FM wire antenna

• Remote control

• Owner’s manual

• Quick Start Guide

Placing the Receiver

Please note the following points:

• Do not place objects directly on top of

this unit. This prevents proper heat
dispersal.

• When installing on a rack or shelf, be

sure to leave more than 8 inches (20
cm.) of space above the receiver.

DOW

STA

TIO

TUN

EDIT

INP

ATT

DIM

CLA

BAN

MPX

STA

NDA

RD ADV

ANC

SUR

ROU

STE

REO

DIR

ECT

SIG

NAL

SEL

ECT

INPU

SEL

MASTER

LTI

JOG

DIO/VID

MUL

TI-C

NNEL

REC

EIV

STA

NDBY

STA

NDB

Y/O

PHO

NES

TUN

ING

NITO

MUL

JOG

MUL

JOG

MID

NIG

LOU

DNE

TON

ICK

SET

LIST

ENIN

N∫m

Û.,,

Avoiding Magnetic
Interference

Make sure not to bend the cables over the
top of this unit (as shown in the
illustration). If this happens, the magnetic
field produced by the transformers in this
unit may cause a humming noise from the
speakers.

Installing the Batteries

The remote control operates on two AA
batteries (not supplied). We recommend
RadioShack alkaline batteries for longest life.

Cautions:

Incorrect use of batteries may result in such
hazards as leakage and bursting. Observe
the following precautions:

• Never use new and old batteries together.

• Insert the plus and minus sides of the

batteries properly according to the marks
in the battery case.

• Batteries with the same shape may have

different voltages. Do not use different
batteries together.

• When disposing of used batteries, please

comply with governmental regulations or
environmental rules that apply in your
country or area.

Introductory Information

31_5021.RCA.01.08

03.3.17, 8:24 PM

Содержание Professional series

















































Результаты поиска

Содержание Professional series

Отзывы:

Бренды по названию

Популярные бренды

RCA Professional series, Руководство пользователя

Результаты поиска

Содержание Professional series

Отзывы:

Бренды по названию

Популярные бренды