background image

 

  

  SenSmart 6000 wiring 

3

Remote 

Sensor

 

 

 

1.

 

Connect 10-30VDC power lead to TB1.1. 

(See Figure 1)

 

2.

 

Connect Common (ground) lead to TB1.4 

(See Figure 1)

 

FOR ANALOG OUTPUT:

 

3.

 

Connect signal lead to TB1.2. (Channel 1) and/or 

 

 

TB1.3 (Channel 2) (4-20mA Out) 

(See Figure 1)

 

FOR ETHERNET OUTPUT:

  

4. 

Connect Ethernet cable to J3. (Ethernet output) 

  

(See Figure 1)

 (optional)

 

 

(By default, DHCP is enabled on the transmitter,

 

 

allowing the device to be discovered by its IP 

  address.)

 

 Installation of Gas Detector

 

Remove windowed lid from unit.

 

1. 

AL Enclosure - 

  

a.

  

Loosen lid set screw

  

b.

  

Rotate lid clockwise and remove

  

c.

  

Loosen thumb screws on display to remove 

 

 

 

display and access terminals

 

2

PY Enclosure - 

  

a.

 

Unscrew lid screws (4) to access terminals.

 

 

What you need (not included)

 

1.

 

Small Flathead Screwdriver

 

2

Phillips Screwdriver (for poly enclosure)

 

3

. Wire 

(RC Systems recommends: Belden 3124A 

 

 

Multi-Conductor wire or equivalent.) 

 

  

Figure 1

Содержание SenSmart 6000













Отзывы: