background image

FUTERA FUSION INSTALLATION AND OPERATION INSTRUCTIONS

46

 

 

 

MACODE-3

NOTICE!

Commonwealth of Massachusetts 

Installation Requirements

(a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building 
or structure used in whole or in part for residential purposes, including those owned or operated 
by the commonwealth and where the side wall exhaust vent termination is less than seven (7) feet 
above fi nished grade, in the area of the venting, including but not limited to decks and porches, 
the following requirements shall be satisfi ed:

1.   INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall 

horizontal vented gas fueled equipment, the installing plumber or gasfi tter shall observe that a hard 
wired carbon monoxide detector with an alarm and battery back-up is installed on the floor level 
where the gas equipment is to be installed. In addition, the installing plumber or gasfi tter shall observe 
that a battery operated or hard wired carbon monoxide detector with an alarm is installed on each 
additional level of the dwelling, building or structure served by the side wall horizontal vented gas 
fueled equipment. It shall be the responsibility of the property owner to secure the services of qualifi ed 
licensed professionals for the installation of hard wired carbon monoxide detectors.

a.   In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl 

space or an attic, the hard wired carbon monoxide detector with alarm and battery back-up may 
be installed on the next adjacent fl oor level.

b.   In the event that the requirements of this subdivision can not be met at the time of completion of 

installation, the owner shall have a period of thirty (30) days to comply with the above requirements; 
provided, however, that during said thirty (30) day period, a battery operated carbon monoxide 
detector with an alarm shall be installed.

2.   APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in 

accordance with the above provisions shall comply with NFPA 720 and be ANSI/UL 2034 listed and 
IAS certifi ed. 

3.   SIGNAGE. A metal or plastic identifi cation plate shall be permanently mounted to the exterior of the 

building at a minimum height of eight (8) feet above grade directly in line with the exhaust vent terminal 
for the horizontally vented gas fueled heating appliance or equipment. The sign shall read, in print 
size no less than one-half (1/2) inch in size, “GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL 
OBSTRUCTIONS”.

4.   INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment 

shall not approve the installation unless, upon inspection, the inspector observes carbon monoxide 
detectors and signage installed in accordance with the provisions of 248 CMR 5.08(2)(a)1 through 4. 

WARNING: Improper venting can result in excessive levels of carbon monoxide which can 
cause severe personal injury or death!

Содержание FUTERA FUSION Series

















































Отзывы: