Razorgage Cyclone RazorOptimal, Руководство пользователя

Страница: 49 / 55

Cyclone RazorOptimal User Manual
49 | P a g e
Technical Services, Inc.
13 ERROR #0009
Drills cannot be started
while the Left Drill ‘End of
Stroke’ switch is on. (Input
X20)

Pocket drills were left
manually extended.

Pocket drills return flow
control is set too low.

Cable or wiring problem.

Proximity switch failed.

Use the valve bank to manually retract drills by pressing the
bottom solenoid button on the left drills valve. See Figure #7.

If pocket drill return flow control is set too low it will not
retract. See
Drill Flow Control section for instruction on
adjusting.

If sensor indicator or PLC input X20 is on without drills being
extended, then there may be a short in the cable or wiring to
PLC input X20. Check for a short and replace cable if
necessary.

If sensor indicator is on without drill being extended and the
cable & wiring check out, then proximity switch has failed.
Replace the sensor.
14 ERROR #0010
Drills cannot be started
while the Right Drill ‘End of
Stroke’ switch is on. (Input
X21)

Pocket drills were left
manually extended.

Pocket drills return flow
control is set too low.

Cable or wiring problem.

Proximity switch failed.

Use the valve bank to manually retract drills by pressing the
bottom solenoid button on the left drills valve. See Figure #7.

If pocket drill return flow control is set too low it will not
retract. See
Drill Flow Control section for instruction on
adjusting.

If sensor indicator or PLC input X21 is on without drills being
extended, then there may be a short in the cable or wiring to
PLC input X21. Check for a short and replace cable if
necessary.

If sensor indicator is on without drill being extended and the
cable & wiring check out, then proximity switch has failed.
Replace the sensor.
15 ERROR #0011
Saw cannot be started unless
ONE of the Scribe Sensors
are on.

Scribe motion is obstructed.

Scribe height is set too high

Low Air Pressure or air leak.

Scribe front or rear cylinder
proximity switch is loose.

Cable or wiring problem

Failed cylinder proximity
switch

Witch system air off check for obstructions in scribe motion. It
should move freely by hand. Remove any wood pieces and
clean out saw dust.

See Machine Adjustment-Scribe Height section for instruction
on lowering the scribe height if necessary.

If scribe is physically not at front or back position, check that
air supply is on and regulator set at the appropriate air pressure.
Check for any leaks in air lines or cylinder.

If the pneumatics to the scribe checks out then check the
proximity switch for the current position. If the sensor is off
check to see if it is loose. Adjust until it is on and tighten if
necessary.

If pneumatics to the scribe cylinder checks out and the switch is
on, check for an open in the cable or wiring to input X22 or
X23 per schematic page 3.

If the cylinder is in position and the cylinder proximity switch
is off, replace the failed switch.
16 MOTION ERROR
(STALL) DURING
PUSHER BAR RUN.

Bar stock or pusher arm are
physically bound up.

The RazorGage speed is set
too high.

The RazorGage accel and/or
decel is set too high for the
application.

Press BACK PUSHER UP button. Remove the source of the
bind and press the RE-SEND THE LAST MOVE button to
resume operation. See figure #8.

Press the RE-SEND THE LAST MOVE button to resume
operation. After bar is completed or if motion error reoccurs,
go to the SETUP SCREEN and check the user parameter speed.
Set the speed to 30 or less.

Press the RE-SEND THE LAST MOVE button to resume
operation. After bar is completed or if motion error reoccurs,
go to the SETUP SCREEN and check the user parameters accel
& decel. Set each to 90 or less.