Raytheon Anschütz Standard 22 GYRO COMPASS Скачать руководство пользователя

Страница: 44 / 104

Operator Unit 130-626.NG002
Standard 22 GYRO COMPASS

4352.DOC010002

2-2

Edition: February 2020

2.2

Setting into Operation

Precondition:
The Operator Unit has to be configured for CAN-Bus operation with the Configuration Tool
AS.

Switch on the power supply to switch on the Operator Unit.

Make sure that the Operator Unit starts.

2.2.1

Heading Indication from Gyro System after Switching on

During the first 3 minutes after switching on (heating stage) it is
possible to activate the quick settling function (see chapter 2.9.6).

The switching on process is divided in the following stages:
(May vary depending on the connected gyro system.)

•

Heating stage

•

Settling stage

Heating Stage
During the heating stage of the gyro system the heading information is not valid, which is
indicated by a set of dashes (- - - .-

). The heating stage is displayed below the heading

information (see Figure 2-1).
If a second gyro is connected, the heating stage is indicated with “(heating)” next to
heading information of the unselected gyro.

Figure 2-1

Heating Stage

Содержание Standard 22 GYRO COMPASS









































































































Результаты поиска

Содержание Standard 22 GYRO COMPASS

Отзывы:

Похожие инструкции для Standard 22 GYRO COMPASS

Бренды по названию

Популярные бренды

Raytheon Anschütz Standard 22 GYRO COMPASS, Руководство оператора и по обслуживанию

Результаты поиска

Содержание Standard 22 GYRO COMPASS

Отзывы:

Похожие инструкции для Standard 22 GYRO COMPASS

Бренды по названию

Популярные бренды