background image

56

LIMITED PARTS WARRANTY

ADVANCED DESIGN BOILER™

SCOPE:

Raypak, Inc. ("Raypak") warrants to the original owner that all parts of this boiler which are actually manufactured by Raypak
will be free from failure under normal use and service for the specified warranty periods and subject to the conditions set forth
in this Warranty. Labor charges and other costs for parts removal or reinstallation, shipping and transportation are not cov-
ered by this Warranty but are the owner's responsibility.

HEAT EXCHANGER WARRANTY:

° Ten (10) Years from date of boiler installation. This includes only cupro-nickel with bronze or cast iron waterways.
° Twenty (20) Years from date of boiler installation against "Thermal Shock" (excluded, however, if caused by boiler opera-
tion at large changes exceeding 150°F between the water temperature at intake and boiler temperature, or operating at boiler
temperatures exceeding 230°F).

BLUFF HEAD BODY BURNER WARRANTY:

° Ten (10) Years from date of boiler installation.

ANY OTHER PART MANUFACTURED BY RAYPAK:

One (1) Year warranty from date of boiler installation, or eighteen (18) months from date of factory shipment based on
Raypak's records, whichever comes first.
SATISFACTORY PROOF OF INSTALLATION DATE, SUCH AS INSTALLER INVOICE, IS REQUIRED. THIS WARRANTY
WILL BE VOID IF THE BOILER RATING PLATE IS ALTERED OR REMOVED.

ADDITIONAL WARRANTY EXCLUSIONS:

This warranty does not cover failures or malfunctions resulting from:
1. Failure to properly install, operate or maintain the boiler in accordance with our printed instructions provided;
2. Abuse, alteration, accident, fire, flood and the like;
3. Sediment or lime buildup, freezing, or other conditions causing inadequate water circulation;
4. High velocity flow exceeding boiler design rates;
5. Failure of connected systems devices, such as pump or controller;
6. Use of non-factory authorized accessories or other components in conjunction with the boiler system;
7. Failing to eliminate air from, or replenish water in, the connected water system;
8. Chemical, particulate matter or other airborne contamination of combustion air or use of chemical additives to water.

PARTS REPLACEMENT:

Under this Warranty, Raypak will furnish a replacement for any failed part. The failed part must first be returned to Raypak if
requested, with transportation charges prepaid, and all applicable warranty conditions found satisfied. The replacement part
will be warranted for only the unexpired portion of the original warranty. Raypak makes no warranty whatsoever on parts not
manufactured by it, but Raypak will apply any such warranty as may be provided to it by the parts manufacturer.

TO MAKE WARRANTY CLAIM:

Promptly notify the original installer, supplying the model and serial numbers of the unit, date of installation and description
of the problem. The installer must then notify his Raypak distributor for instructions regarding the claim. If either is not avail-
able, contact Service Manager, Raypak, Inc., 2151 Eastman Avenue, Oxnard, CA 93030 or call (805) 278-5300. In all cases
proper authorization must first be received from Raypak before replacement of any part.

EXCLUSIVE WARRANTY - LIMITATION OF LIABILITY:

This is the only warranty given by Raypak. No one is authorized to make any other warranties on Raypak's behalf. THIS
WARRANTY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. RAYPAK'S SOLE LIA-
BILITY AND THE SOLE REMEDY AGAINST RAYPAK WITH RESPECT TO DEFECTIVE PARTS SHALL BE AS PROVIDED
IN THIS WARRANTY. IT IS AGREED THAT RAYPAK SHALL HAVE NO LIABILITY, WHETHER UNDER THIS WARRANTY,
OR IN CONTRACT, TORT, NEGLIGENCE OR OTHERWISE, FOR ANY SPECIAL, CONSEQUENTIAL, OR INCIDENTAL
DAMAGE, INCLUDING DAMAGE FROM WATER LEAKAGE. Some states do not allow limitations on how long an implied
warranty lasts, or for the exclusion of incidental or consequential damages. So the above limitation or exclusion may not
apply to you.

This Limited Warranty gives you specific legal rights. You may also have other rights which may vary from state to state. We
suggest that you complete the information below and retain this certificate in the event warranty service is needed.
Reasonable proof of the effective date of the warranty (date of installation) must be presented, otherwise, the effective date
will be based on the date of manufacture plus thirty (30) days.

Содержание 751


























































Отзывы: