Raypak 268A Скачать руководство пользователя страница 26

Страница: 26 / 44

Status and Diagnostics

The heaters are programmed to display a variety of status

and diagnostic messages, depending on the operating

conditions.
The following heat status messages are displayed in Pool,

Spa, and Remote modes when there are no active fault

conditions.

Display

Condition

Heating

Call for heat established, flame present.

Spark

Spark operating.

No Demand

Heat demand is satisfied.

Table L. Heater Status Messages - No Active Faults

The following conditions are displayed in Pool, Spa and

Remote modes.

Display

Condition

Sensor Failure

Thermistor temperatures disagree by

more than 2°F (1°C).

Sensor Open

Thermistor sensor failed open. Below

-20°F (-29°C).

Sensor Short

Thermistor sensor failed short. Above

217°F (103°C).

Flame w/o CFH

Board is sensing flame when

both main and pilot valves are

commanded shut.

PV Output Fault

Pilot gas valve output is not in

commanded state.

MV Output Fault

Main gas valve output is not in

commanded state.

LoNox Tab Fault

Voltage is sensed at the Lo NOx

terminal on a non -Lo- NOx heater

(Lo NOx tab is intact).

Internal Fault

Board fault, replace board.

EEPROM Fault

Memory fault, reset setpoints, replace

board if fault does not clear.

Clock/Fireman Sw

Time clock/fireman switch circuit is

open.

Low Temp

Lockout

Water temperature below 36°F (2°C).

Table M. Heater Status Messages - Active Faults

The following conditions are displayed only while there is a

demand for heat present.

Display

Condition

Water Sw Open

Water pressure switch open.

Vent/Field

Sw #1

Vent spill switch/field switch #1 open.

Hi Limit 1 Fault

High limit 1 open.

Hi Limit 2 Fault

High limit 2 open.

Rollout Sw Open

Rollout switch open.

Flow/Field SW #2

Field-supplied flow switch/field switch

#2 open.

Ignition Lockout

(Propane Tab

Broken)

Alternating with “No pilot sensed”

- Pilot flame not established within the

required time (15 sec or 90 sec).

Alternating with “Main Ign Failure”

- Pilot flame lost during the 8 second

trial to ignite the main burner.

Ignition Failure

(Propane Tab Not

Broken)

Alternating with “No pilot sensed”

- Pilot flame not established within 90

seconds.

Ign 60 min Delay

(Propane Tab Not

Broken)

Alternating with “Main Ign Failure”

- Pilot flame lost 4 times within the 8

second trial to ignite the main burner.

Heater will lockout for 60 minutes

before retrying.

Table N. Heater Status Messages - Demand for Heat

RELEASED

For Reference Only

Содержание 268A













































Результаты поиска

Содержание 268A

Отзывы:

Похожие инструкции для 268A

Бренды по названию

Популярные бренды

Raypak 268A, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 268A

Отзывы:

Похожие инструкции для 268A

Бренды по названию

Популярные бренды