background image

Gas-Fired Pool 

and Spa Heater

Catalog No. 6000.64F

Effective: 07-03-20

Replaces: 03-03-20

P/N 241452 Rev. 7

AS

ME

HLW

INSTALLATION AND  

OPERATION MANUAL

Atmospheric Models 

268A and 408A

This manual should be maintained in legible condition and kept adjacent to the heater or in a safe place for future 

reference.

A

WARNING:

 If the information in the instructions is not followed exactly, a fire or explosion may result 

causing property damage, personal injury or death. 

- Do not store or use gasoline or other flammable vapors and liquids or other combustible materials in 

the vicinity of this or any other appliance. To do so may result in an explosion or fire.

- WHAT TO DO IF YOU SMELL GAS

 

•   Do not try to light any appliance.

  •   Do not touch any electrical switch; do not use any phone in your building.
  •   Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
  •   If you cannot reach your gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer, service agency or the gas supplier.

TM

RELEASED

For Reference Only

Содержание 268A













































Отзывы: