Raypak 1259B Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 52

background image

INSTALLATION

INSTALLATION

Installation Codes

Installations must follow these codes:

•

Local, state, provincial, and national codes, laws,
regulations and ordinances

•

National Fuel Gas Code, ANSI Z223.1/NFPA 54 –
latest edition (NFGC)

•

National Electrical Code, ANSI/NFPA 70 - latest
edition (NEC)

•

Standard for Controls and Safety Devices for
Automatically Fired Boilers, ANSI/ASME CSD-1,
when required (CSD-1)

•

For Canada only: CAN/CGA B149 Installation
Code (B149) and CSA C22.1 C.E.C. Part 1
(C22.1)

The temperature of the water in the heater can be reg-
ulated by using the temperature controller. To comply
with safety regulations, the temperature controller is
set at the lowest setting when shipped from the facto-
ry.

To adjust the water temperature, insert a small straight
screwdriver into the adjustment screw on the front of
temperature controller and turn the wheel to the
desired setting (See Fig. 4.).

CAUTION:

Hotter water increases the risk of scald-

ing! There is a hot water scald potential if the
thermostat is set too high.

Fig. 4: Temperature Control

Equipment Base

The heater should be mounted on a level, structurally
sound surface. The heater is approved for installation
on a combustible surface but must NEVER be
installed on carpeting. Gas-fueled equipment installed
in enclosed parking garages must be located at least
18 in. above the floor.

Stacking

Delta Limited units can be stacked two units high with
an optional stacking rack. A stacking kit is available
from Raypak for this type of installation.

CAUTION:

The heaters should be located in an

area where water leakage will not result in damage
to the area adjacent to the appliances or to the
structure. When such locations cannot be avoided, it
is recommended that a suitable catch pan,
adequately drained, be installed under the
appliance. The pan must not restrict air flow.

REQUIRES OPTIONAL VENT TEE.

REQUIRES OPTIONAL VENT TEE IF VENTED OUT BACK

OF HEATER.

Fig. 5: Typical Stacked Installation

9

«
...
7
8
9
10
11
...
»

Содержание 1259B





















































Отзывы:

Нет отзывов

Похожие инструкции для 1259B

Бренд: Rheem Страницы: 25

Бренд: Sime Страницы: 12

Бренд: Vaillant Страницы: 52

Бренд: Kiturami Страницы: 45

Mighty Therm HH 1010

Бренд: Laars Страницы: 28

Бренд: Laars Страницы: 44

Бренд: Sime Страницы: 100

Бренд: Sime Страницы: 100

Бренд: Columbia Страницы: 56

UB INOX SOLAR 200-2

Бренд: Immergas Страницы: 16

Maior Eolo 24 4E

Бренд: Immergas Страницы: 36

Бренд: Rapido Страницы: 36

MAGIS VICTRIX ERP

Бренд: Immergas Страницы: 48

Heatmax Combi 24 HE

Бренд: Potterton Страницы: 60

LOGIC COMBI2 C24

Бренд: Ideal Heating Страницы: 70

Main Eco Elite Combi 25

Бренд: Main Heating Страницы: 20

Бренд: Weishaupt Страницы: 132

Concord CXD 40-100

Бренд: Ideal Boilers Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды